Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › 2012.12–2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0062871 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2652 Front Vertical Sensor Malfunction The upward and downward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Front vertical motor (Separate type front seat cushion spring assembly)

·

Harness or connector



WIRING DIAGRAM

B342142
4.729,3.875 6.75,4.5 2.021,0.625 10 Position Control ECU and Switch Assembly 0.802,3.844 2.948,4.427 2.146,0.583 10 Separate Type Front Seat Cushion Spring Assembly 1.104,3.083 1.563,3.281 0.458,0.198 10 e13 1.115,3.25 2.583,3.542 1.469,0.292 10 Front Vertical Motor 2.26,1.073 2.417,1.271 0.156,0.198 10 4 2.229,1.573 2.385,1.771 0.156,0.198 10 1 2.24,2.083 2.448,2.323 0.208,0.24 10 2 2.229,2.573 2.385,2.771 0.156,0.198 10 3 4.802,1.198 5.26,1.396 0.458,0.198 10 e18 4.802,1.698 5.26,1.896 0.458,0.198 10 e18 4.844,2.198 5.156,2.396 0.313,0.198 10 e6 4.844,2.698 5.156,2.896 0.313,0.198 10 e6 4.917,0.979 5.073,1.177 0.156,0.198 10 8 4.906,1.458 5.063,1.656 0.156,0.198 10 5 4.896,1.979 5.052,2.177 0.156,0.198 10 3 4.885,2.51 5.042,2.708 0.156,0.198 10 1 5.177,1.198 5.792,1.396 0.615,0.198 10 FRV+ 5.167,1.688 5.781,1.885 0.615,0.198 10 FRV- 5.135,2.188 5.75,2.385 0.615,0.198 10 SSFV 5.146,2.708 5.76,2.906 0.615,0.198 10 SGND

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FRONT VERTICAL MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
OK:

Motor operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)

NG

5.INSPECT FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)
a.
E118523
1.49,0.344 1.896,0.615 0.406,0.271 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.573,0.375 1.938,0.594 0.365,0.219 10 false e13
*a Front view of wire harness connector
(to Front Vertical Motor [Separate Type Front Seat Cushion Spring Assembly])


Disconnect the e13 front vertical motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e13-2 - e13-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
3.CHECK FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.
B238515
1.542,0.271 1.917,0.531 0.375,0.26 0.125,0.063 0.302,0.229 0.177,0.167 10 *a 1.625,0.313 1.979,0.542 0.354,0.229 10 e13
*a Component with harness connected
(Front Vertical Motor [Separate Type Front Seat Cushion Spring Assembly])


Reconnect the e13 front vertical motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e13-2 - Body ground Front vertical switch on 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
a.

Disconnect the e6 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-3 (SSFV) - e13-2 Always Below 1 Ω
e6-1 (SGND) - e13-3 Always Below 1 Ω
e6-3 (SSFV) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)
a.

Remove the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)

NG

REPLACE FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
a.

Disconnect the e18 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e18-8 (FRV+) - e13-4 Always Below 1 Ω
e18-5 (FRV-) - e13-1 Always Below 1 Ω
e18-8 (FRV+) - Body ground Always 10 kΩ or higher
e18-5 (FRV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR