When the position control ECU and switch assembly does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2653 | Lifter Sensor Malfunction | The upward and downward lock detection position of the sensor is the same. | ·
Position control ECU and switch assembly ·
Lifter motor (Separate type front seat cushion spring assembly) ·
Harness or connector |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Tester Display |
|---|
| Lifter Operation |
Motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Lifter Motor [Separate Type Front Seat Cushion Spring Assembly]) |
Disconnect the e14 lifter motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| e14-2 - e14-3 | Lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Lifter Motor [Separate Type Front Seat Cushion Spring Assembly]) |
Reconnect the e14 lifter motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| e14-2 - Body ground | Lifter switch on | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e6 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e6-4 (SSRL) - e14-2 | Always | Below 1 Ω |
| e6-1 (SGND) - e14-3 | Always | Below 1 Ω |
| e6-4 (SSRL) - Body ground | Always | 10 kΩ or higher |
| e6-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the separate type front seat cushion spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY
Inspect the separate type front seat cushion spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e18 position control ECU and switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e18-10 (LFT+) - e14-4 | Always | Below 1 Ω |
| e18-12 (LFT-) - e14-1 | Always | Below 1 Ω |
| e18-10 (LFT+) - Body ground | Always | 10 kΩ or higher |
| e18-12 (LFT-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG