Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › 2012.12–2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0062871 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When either the M1 or M2 switch is pressed, the main body ECU (multiplex network body ECU) sends a switch signal to the seat memory switch via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU and switch assembly. The position control ECU and switch assembly operates each motor to achieve each memorized position value.

WIRING DIAGRAM

B342200E01
5.167,2.719 6.583,2.938 1.417,0.219 10 false Seat Memory Switch 5.156,2.542 5.615,2.74 0.458,0.198 10 false J13 5.365,1.99 5.521,2.188 0.156,0.198 10 false E 5.365,0.917 5.823,1.115 0.458,0.198 10 false MRY 5.354,1.313 5.667,1.51 0.313,0.198 10 false M2 5.365,1.698 5.677,1.896 0.313,0.198 10 false M1 4.188,1.708 4.5,1.906 0.313,0.198 10 false M1 4.188,1.323 4.5,1.521 0.313,0.198 10 false M2 4.156,0.927 4.469,1.125 0.313,0.198 10 false MM 5.156,0.813 5.313,1.01 0.156,0.198 10 false 2 5.167,1.208 5.323,1.406 0.156,0.198 10 false 4 5.167,1.563 5.323,1.76 0.156,0.198 10 false 3 5.156,1.885 5.313,2.083 0.156,0.198 10 false 1 4.49,1.583 4.802,1.781 0.313,0.198 10 false 25 4.49,1.208 4.802,1.406 0.313,0.198 10 false 23 4.49,0.823 4.802,1.021 0.313,0.198 10 false 26 0.781,3.427 4.448,3.625 3.667,0.198 10 false : CAN Communication Line 3.042,2.635 4.677,3.104 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 3.042,2.427 3.5,2.625 0.458,0.198 10 false G79 0.656,2.458 2.01,2.865 1.354,0.406 10 false Position Control ECU and Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>PROBLEM SYMPTOMS TABLE

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
a.

Check that each function of the power seat operates normally by using the switches on the power seat switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the switches on the power seat switch.



Result:
Proceed to
OK
NG



OK

2.CHECK SEAT POSITION MEMORY FUNCTION

NG

2.CHECK SEAT POSITION MEMORY FUNCTION
a.

Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.




Result:
Proceed to
Seat position memory function is normal
Seat position memory function is not normal



Seat position memory function is normal

3.CHECK SEAT POSITION RESTORING FUNCTION

Seat position memory function is not normal

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

3.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 switch or M2 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

·

Ignition switch is off.

·

The ignition switch is ON, and the shift lever is in P.*1

·

The ignition switch is turned off within 180 seconds after the driver door is closed and opened.*2

·

The ignition switch is turned off within 60 seconds after the driver door is opened and closed.*3



Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C



A

4.READ VALUE USING GTS (SEAT MEMORY)

B

9.READ VALUE USING GTS (P SWITCH)

C

10.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
4.READ VALUE USING GTS (SEAT MEMORY)
a.

Store a seat position in memory for each of the M1 and M2 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Driver Seat / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

Mem appears on the GTS screen.



Result:
Proceed to
OK
NG



OK

5.REPLACE SEAT MEMORY SWITCH

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

5.REPLACE SEAT MEMORY SWITCH
a.

Replace the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK SEAT POSITION RESTORING FUNCTION
6.CHECK SEAT POSITION RESTORING FUNCTION

b.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.




Result:
Proceed to
Seat position restoring function operates normally
Seat position restoring function does not operate normally



Seat position restoring function operates normally

END (SEAT MEMORY SWITCH WAS DEFECTIVE)

Seat position restoring function does not operate normally

7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK SEAT POSITION RESTORING FUNCTION
8.CHECK SEAT POSITION RESTORING FUNCTION


c.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.




Result:
Proceed to
Seat position restoring function operates normally
Seat position restoring function does not operate normally



Seat position restoring function operates normally

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

Seat position restoring function does not operate normally

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

9.READ VALUE USING GTS (P SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Switch Park state signal ON or OFF ON: Shift lever in P
OFF: Shift lever in a position other than P
-
Body Electrical > Driver Seat > Data List
Tester Display
P Switch
50003 162 13
OK:

On the GTS screen, the item changes between ON and OFF according to the above.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

10.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly signal ON or OFF ON: Driver door open
OFF: Driver door closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

On the GTS screen, the item changes between ON and OFF according to the above.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)