DTC B1794 is stored when a malfunction is detected in the occupant detection ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1794 | Open in Occupant Classification ECU Battery Positive Line | One of the following conditions is met:
·
Occupant detection ECU circuit malfunction. ·
Occupant detection ECU malfunction. ·
Occupant detection ECU detects a short circuit to ground signal in the front passenger side buckle switch circuit for 2 seconds. |
·
Harness or connector ·
Occupant detection ECU |
When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1794 of the occupant classification system.
Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1794 is not output |
| DTC B1794 is output |
DTCs other than DTC B1794 may be output at this time, but they are not related to this check.
DTC B1794 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1794 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly, rear occupant classification sensor LH and RH and occupant detection ECU.
| Proceed to |
|---|
| Connectors are properly connected |
| Connectors are not properly connected |
Connectors are properly connected
Connectors are not properly connected
Disconnect the connector from the occupant detection ECU.
Check that the connectors (on the occupant detection ECU side) are not damaged.
| Proceed to |
|---|
| Connectors are not deformed or damaged |
| Connectors are deformed or damaged |
Connectors are not deformed or damaged
Connectors are deformed or damaged
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d16-1 - Body ground | Always | 11 to 14 V |
| d16-6 - Body ground | Ignition switch ON |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d16-3 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the occupant detection ECU.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1794 is not output |
| DTC B1794 is output |
DTCs other than DTC B1794 may be output at this time, but they are not related to this check.
DTC B1794 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1794 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Perform the inspection using parts from a normal vehicle when possible.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
"Zero Point Calibration is complete." is displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| NEXT |
NEXT