Home › Engine / Hybrid System › 1AD-FTV STARTING › STARTER(w/ Stop And Start System) › 2013.11–2015.10
RM3090E _51 Engine / Hybrid System _008740 1AD-FTV STARTING _0103788 STARTER(w/ Stop And Start System) G

1AD-FTV STARTING  STARTER(w/ Stop And Start System)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used.

Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


a.

Perform a pull-in test.

i.

Remove the nut and disconnect the field coil wire from terminal C.


ii.
A291386
1.781,0.438 2.083,0.167 2.083,0.167 2.25,0.167 true 0.563,0.563 1.646,0.563 true 0.417,0.469 0.729,0.625 0.313,0.156 10 false *a 2.271,0.063 2.583,0.219 0.313,0.156 10 false *b
*a Terminal C
*b Terminal 50


Connect the battery to the starter magnetic switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the starter magnetic switch assembly.



b.
A291387
0.5,1.438 0.656,1.635 0.156,0.198 10 false .
V100135

Disconnect


Perform a holding test.

i.

When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear remains out.

If the clutch pinion gear moves inward, replace the starter magnetic switch assembly.



c.
A297123
0.5,1.073 0.656,1.271 0.156,0.198 10 false .
V100135

Disconnect


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not move inward, replace the starter magnetic switch assembly.



d.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


ii.

Mount the starter assembly in a vise between aluminum plates.


iii.
A297124
1.5,0.417 2.25,0.417 true 0.458,0.302 1.375,0.302 true 0.833,1.5 0.833,1.333 0.833,1.333 1.354,0.552 true 0.313,0.208 0.625,0.365 0.313,0.156 10 false *a 2.26,0.333 2.573,0.49 0.313,0.156 10 false *b 0.76,1.51 1.073,1.667 0.313,0.156 10 false *c
*a Terminal 30
*b Terminal 50
*c Terminal C


Connect the battery and an ammeter to the starter assembly as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the clutch pinion gear is moving outward. Then measure the current.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 190 A


If the current is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the surface of the commutator for dirt and burns.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe. If necessary, replace the starter armature assembly.


b.

Inspect the resistance of the commutator.

If there is no continuity between any segments, replace the starter armature assembly.

i.
A297125

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the resistance is not as specified, replace the starter armature assembly.


ii.
A297126

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the resistance is not as specified, replace the starter armature assembly.



c.

Check the surface of the commutator for dirt and burns.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe. If necessary, replace the starter armature assembly.


d.
A297127

Using a vernier caliper, measure the commutator diameter.

Standard Diameter:

35.0 mm (1.37 in.)


Minimum Diameter:

34.0 mm (1.34 in.)


HINT:

Be sure to measure the commutator diameter at the ridges.


If the diameter is less than the minimum, replace the starter armature assembly.


e.

Check the commutator circle runout.

i.
A145291
0.594,0.896 0.417,0.333 0.417,0.333 0.25,0.333 true 1.958,1.573 1.5,1.917 1.5,1.917 1.333,1.917 true 0.115,0.24 0.427,0.396 0.313,0.156 10 *1 1.188,1.823 1.5,1.979 0.313,0.156 10 *1
*1 Armature Shaft


Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



f.
A297128

Check that the undercut portion is clean and free of foreign matter. Smooth out the edge.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


HINT:

Be sure to measure the commutator undercut depth at a cutout.


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

a.

Inspect the resistance of the field coil.

i.
A165175

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead wire - Brush Always Below 1 Ω


If the resistance is not as specified, replace the starter yoke assembly.


ii.
A165176

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Brush - Starter yoke body Always 10 kΩ or higher


If the resistance is not as specified, replace the starter yoke assembly.



Hide 4.INSPECT BRUSH

a.
A165177
0.333,0.281 0.646,0.438 0.313,0.156 10 false *a 0.333,2.5 0.646,2.656 0.313,0.156 10 false *b 0.844,1.938 1.156,2.094 0.313,0.156 10 false *c 2.385,4.25 2.698,4.406 0.313,0.156 10 false *c
*a Starter Brush Holder Assembly Side
*b Starter Yoke Assembly Side
*c Length


Using a vernier caliper, measure the brush length.

Standard Length:

15.0 mm (0.591 in.)


Minimum Length:

9.0 mm (0.354 in.)


HINT:

Be sure to measure the brush lengths at the protrusions.


If the length is less than the minimum, replace the starter brush holder assembly.


Hide 28140 5.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Inspect the insulation.

i.
A297129

Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

Standard Resistance:

10 kΩ or higher


If the resistance is not as specified, replace the starter brush holder assembly.



b.

Inspect the load of the brush spring.

i.
A297130
0.917,1.667 1.417,1.667 true 2.25,1.417 2.75,1.417 true 0.771,1.563 1.083,1.719 0.313,0.156 10 *1 2.771,1.313 3.083,1.469 0.313,0.156 10 *2
*1 Brush
*2 Brush Spring


Take the pull scale reading immediately after the brush spring separates from the brush.

Standard Spring Installed Load:

21.5 to 27.5 N (2 to 3 kgf, 4.8 to 6.2 lbf)


Minimum Spring Installed Load:

12.3 N (1 kgf, 2.8 lbf)


If the load is less than the minimum, replace the starter brush holder assembly.



Hide 28021 6.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth of the planetary gear and starter center bearing clutch sub-assembly for wear or damage.

If any gear of the starter center bearing clutch sub-assembly is damaged, replace the starter center bearing clutch sub-assembly.


b.
A165178
2.146,0.521 2.458,0.677 0.313,0.156 10 *a 1.656,1.438 1.969,1.594 0.313,0.156 10 *b
*a Free
*b Lock


Check the movement of the clutch pinion gear.

i.

Rotate the clutch pinion gear clockwise, and check that it turns freely.


ii.

Try to rotate the clutch pinion gear counterclockwise, and check that it locks.

If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.



Hide 28226A 7.INSPECT STARTER MAGNETIC SWITCH ASSEMBLY

a.
A290533

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the starter magnetic switch assembly.



b.
A211507
1.583,0.885 1.917,0.25 1.917,0.25 2.083,0.25 true 1.833,1.896 1.833,1.396 true 2.104,0.156 2.417,0.313 0.313,0.156 10 false *a 1.76,1.896 2.01,2.063 0.25,0.167 10 false *b
*a Terminal 50
*b Terminal C


Check if the pull-in coil has an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the resistance is not as specified, replace the starter magnetic switch assembly.



c.

Check if the holding coil has an open circuit.

i.
A165173
1.573,0.885 2.083,0.5 2.083,0.5 2.25,0.5 true 2.271,0.406 2.583,0.563 0.313,0.156 10 false *a
*a Terminal 50


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the resistance is not as specified, replace the starter magnetic switch assembly.