RM3090E
_V1
General
_009232
SPECIFICATIONS
_0050403
1AD-FTV STARTING
F
SPECIFICATIONS 1AD-FTV STARTING SERVICE DATA
GLOW PLUG
| Tester Connection
|
Condition
|
Specified Condition
|
| Glow plug terminal - Body ground
|
20°C (68°F)
|
0.28 Ω or higher
|
STARTER ASSEMBLY (w/ Stop And Start System)
| Tester Connection
|
Condition
|
Specified Condition
|
| Battery positive (+) terminal - Terminal 30 - Terminal 50
|
11.5 V
|
Below 190 A
|
STARTER ASSEMBLY (w/o Stop And Start System)
| Tester Connection
|
Condition
|
Specified Condition
|
| Battery positive (+) terminal - Terminal 30 - Terminal 50
|
11.5 V
|
150 A or less
|
STARTER ARMATURE ASSEMBLY (Standard Resistance)
| Tester Connection
|
Condition
|
Specified Condition
|
| Segment - Segment
|
Always
|
Below 1 Ω
|
| Segment - Coil core
|
Always
|
10 kΩ or higher
|
STARTER ARMATURE ASSEMBLY (w/ Stop And Start System)
| Standard Diameter
|
35.0 mm (1.37 in.)
|
| Minimum Diameter
|
34.0 mm (1.34 in.)
|
| Maximum runout
|
0.05 mm (0.00197 in.)
|
| Standard undercut depth
|
0.7 mm (0.0276 in.)
|
| Minimum undercut depth
|
0.2 mm (0.00787 in.)
|
STARTER ARMATURE ASSEMBLY (w/o Stop And Start System)
| Standard Diameter
|
29.0 mm (1.14 in.)
|
| Minimum Diameter
|
28.0 mm (1.10 in.)
|
| Maximum runout
|
0.05 mm (0.00197 in.)
|
| Standard undercut depth
|
0.4 mm (0.0157 in.)
|
| Minimum undercut depth
|
0.2 mm (0.00787 in.)
|
STARTER YOKE ASSEMBLY (w/ Stop And Start System)
| Tester Connection
|
Condition
|
Specified Condition
|
| Lead wire - Brush
|
Always
|
Below 1 Ω
|
| Brush - Starter yoke body
|
Always
|
10 kΩ or higher
|
BRUSH (w/ Stop And Start System)
| Standard Length
|
15.0 mm (0.591 in.)
|
| Minimum Length
|
9.0 mm (0.354 in.)
|
BRUSH (w/o Stop And Start System)
| Standard Length
|
14.4 mm (0.567 in.)
|
| Minimum Length
|
9.0 mm (0.354 in.)
|
STARTER BRUSH HOLDER ASSEMBLY (w/ Stop And Start System)
| Standard Resistance
|
10 kΩ or higher
|
| Brush Spring
|
Standard Spring Installed Load
|
21.5 to 27.5 N (2 to 3 kgf, 4.8 to 6.2 lbf)
|
| Minimum Spring Installed Load
|
12.3 N (1 kgf, 2.8 lbf)
|
STARTER BRUSH HOLDER ASSEMBLY (w/o Stop And Start System)
| Brush Spring
|
Standard Spring Installed Load
|
22.3 to 27.3 N (2 to 3 kgf, 5.0 to 6.1 lbf)
|
| Minimum Spring Installed Load
|
13.8 N (1 kgf, 3.1 lbf)
|
STARTER MAGNETIC SWITCH ASSEMBLY
| Tester Connection
|
Condition
|
Specified Condition
|
| Terminal 50 - Terminal C
|
Always
|
Below 1 Ω
|
| Terminal 50 - Switch body
|
Always
|
Below 2 Ω
|
STARTER RELAY (ST)
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage applided to terminals 1 and 2
|
Below 1 Ω
|
GLOW PLUG RELAY
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
Battery voltage not applied to terminals 3 and 4
|
10 kΩ or higher
|
| Battery voltage applided to terminals 3 and 4
|
Below 1 Ω
|