Home › Drivetrain › EA64 MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2013.11
RM3090E _52 Drivetrain _008755 EA64 MANUAL TRANSMISSION / TRANSAXLE _0048559 DIFFERENTIAL CASE A

EA64 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 41311E 1.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C287707
0.635,1.208 0.385,0.823 0.385,0.823 0.656,0.646 false 2.542,0.854 2.417,0.75 2.417,0.75 2.646,0.781 false 2.115,0.656 2.479,0.854 0.365,0.198 10 true SST 0.073,0.75 0.531,0.948 0.458,0.198 10 false SST 1.958,0.167 2.417,0.365 0.458,0.198 10 false *a 0.219,0.104 0.677,0.302 0.458,0.198 10 false *b
*a Turn
*b Hold


Using SST, remove the front differential case front tapered roller bearing from the front No. 1 differential case sub-assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00490)


Hide 41311F 2.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C287708
0.667,1.271 0.417,0.917 0.417,0.917 0.667,0.74 false 2.521,1.229 2.385,1.083 2.385,1.083 2.625,1.156 false 0.104,0.833 0.563,1.031 0.458,0.198 10 false SST 2.083,1 2.469,1.198 0.385,0.198 10 true SST 1.979,0.302 2.292,0.458 0.313,0.156 10 false *a 0.177,0.188 0.49,0.344 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front differential case rear tapered roller bearing from the front No. 1 differential case sub-assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00490)


Hide 41221 3.REMOVE FRONT DIFFERENTIAL RING GEAR

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.

·

Do not overtighten the vise.




b.
C287709
1.948,0.479 2.677,0.49 2.677,0.49 1.906,0.615 false 2.771,0.385 3.083,0.542 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front No. 1 differential case sub-assembly.


c.
C117490

Remove the 16 bolts.


d.

Using a plastic-faced hammer, remove the front No. 1 differential case sub-assembly from the front differential ring gear.


Hide 41301L 4.INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41342A 5.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C290676

Using a 5 mm pin punch and hammer, remove the front differential pinion shaft straight pin from the front No. 1 differential case sub-assembly.


Hide 41342F 6.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C287710

Remove the front No. 1 differential pinion shaft from the front No. 1 differential case sub-assembly.


Hide 7.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41331F 8.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Set SST as shown in the illustration and tighten it.

C290677C01
4.521,0.365 5.031,0.365 false 4.938,1.677 4.323,1.573 4.323,1.573 4.938,1.458 true 3.208,0.427 3.521,0.583 0.313,0.156 10 false *a 0.854,2.448 1.167,2.604 0.313,0.156 10 false *b 4.188,0.292 4.646,0.49 0.458,0.198 10 false SST 4.01,1.5 4.469,1.698 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, conical spring, front No. 1 differential side gear thrust washer and front No. 1 differential case sub-assembly.


HINT:
·

Tighten SST until there is a clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C287712
2.333,0.531 2.406,0.531 2.406,0.531 2.469,1.167 false 2.031,0.479 2.49,0.677 0.458,0.198 10 false SST 1.438,0.198 1.75,0.354 0.313,0.156 10 false *a
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front No. 1 differential case sub-assembly.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



c.
C287713C01
1.729,0.26 2.219,0.26 true 2.198,1.292 1.667,0.771 1.667,0.771 2.146,0.771 true 1.74,0.542 2.052,0.542 2.052,0.542 2.24,0.417 true 1.76,1.802 2.25,1.802 true 1.74,2.031 2.083,2.031 2.083,2.031 2.219,1.948 true 1.49,0.698 1.802,0.854 0.313,0.156 10 false *1 1.563,0.469 1.875,0.625 0.313,0.156 10 false *2 1.542,0.198 1.854,0.354 0.313,0.156 10 false *3 1.573,1.74 1.885,1.896 0.313,0.156 10 false *2 1.563,1.979 1.875,2.135 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 conical spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front No. 1 differential case sub-assembly, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front No. 1 differential case sub-assembly.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and conical spring.