Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2013.11–2015.04
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C279317
0.938,0.438 2.156,0.656 1.219,0.219 10 false from IG Circuit 3.146,0.625 4.365,0.844 1.219,0.219 10 false ECU-IG NO. 2 0.354,1.948 2.052,2.188 1.698,0.24 10 false *1: for FMVSS138 Type 0.365,2.219 2.073,2.458 1.708,0.24 10 false *2: for ECE-R64 Type 0.354,2.49 2.448,2.75 2.094,0.26 10 false *3: w/o Stop and Start System 4.802,0.292 5.073,0.552 0.271,0.26 10 false 1 4.74,1.479 5.01,1.74 0.271,0.26 10 false 12 5.052,0.438 5.458,0.646 0.406,0.208 10 false IG 5.021,1.542 5.427,1.75 0.406,0.208 10 false E*1, 5,1.74 5.552,1.948 0.552,0.208 10 false GND*2 4.615,2.104 5.802,2.385 1.188,0.281 10 false M11*1, M30*2 4.583,2.313 7.156,2.708 2.573,0.396 10 false Tire Pressure Warning ECU and Receiver 0.74,1.417 2.885,1.719 2.146,0.302 10 false Engine Stop and Start ECU*4 0.417,1.417 0.906,1.688 0.49,0.271 10 false G87 3.052,0.969 3.323,1.229 0.271,0.26 10 false *4 1.51,1.094 2,1.354 0.49,0.26 10 false IGO1 1.969,0.958 2.24,1.219 0.271,0.26 10 false 12 2.333,1.927 4.281,2.198 1.948,0.271 10 false *4: w/ Stop and Start System 4.01,0.292 4.281,0.552 0.271,0.26 10 false *3

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU - BATTERY AND BODY GROUND)
a.
E198671C01
0.25,0.49 0.667,0.76 0.417,0.271 0.25,0.927 0.667,1.198 0.417,0.271 1.24,1.427 0.5,1.583 0.5,1.583 0.5,1.75 true 2.063,1.625 2.49,1.667 true 0.083,0.083 0.396,0.281 0.313,0.198 10 *a 0.323,0.552 0.781,0.75 0.458,0.198 10 M11 0.333,1 0.792,1.198 0.458,0.198 10 M30 0.688,0.49 1,0.688 0.313,0.198 10 *A 0.688,0.885 1,1.083 0.313,0.198 10 *B 0.448,1.771 0.76,1.969 0.313,0.198 10 IG 2.583,1.552 3.25,1.75 0.667,0.198 10 E *A 2.583,1.74 3.323,1.917 0.74,0.177 10 GND *B
*A for FMVSS138 Type
*B for ECE-R64 Type
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the tire pressure warning ECU and receiver M11*1 or M30*2 connector.

*1: for FMVSS138 Type

*2: for ECE-R64 Type



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for FMVSS138 Type:
Tester Connection Switch Condition Specified Condition
M11-1 (IG) - Body ground Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V

for ECE-R64 Type:
Tester Connection Switch Condition Specified Condition
M30-1 (IG) - Body ground Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for FMVSS138 Type:
Tester Connection Condition Specified Condition
M11-12 (E) - Body ground Always Below 1 Ω

for ECE-R64 Type:
Tester Connection Condition Specified Condition
M30-12 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR