Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.TABLE OF BOLT, SCREW AND NUT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.REMOVE UPPER INSTRUMENT PANEL
58901A
5.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY
55433B
6.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Detach the 8 clips and remove the lower No. 2 instrument panel finish panel.
| *A | w/ Drive Mode Switch |
| *B | w/ Seat Heater System |
| *C | w/ PTC Heater |
| *D | for Windshield Deicer |
| *E | w/ USB Audio System |
for LHD:
Disconnect each connector.
| *A | w/ Drive Mode Switch |
| *B | w/ Lane Departure Alert System |
| *C | w/ Seat Heater System |
| *D | w/ USB Audio System |
for RHD:
Disconnect each connector.
55606
7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Remove the 2 screws <A> or <B>.
Detach the 2 claws and 2 guides and remove the No. 1 instrument panel under cover sub-assembly.
w/ Tire Pressure Warning System:
Disconnect the connector.
55545
8.REMOVE FUSE BOX OPENING COVER
|
Protective Tape |
for LHD:
Apply protective tape as shown in the illustration.
Detach the 8 clips and remove the fuse box opening cover.
| *A | w/ Headlight Leveling |
| *B | w/ Light Control Rheostat |
| *C | w/ VSC OFF Switch |
| *D | w/ Blind Spot Monitor |
Disconnect each connector and detach the wire harness clamp.
|
Protective Tape |
for RHD:
Apply protective tape as shown in the illustration.
Detach the 9 clips and remove the fuse box opening cover.
| *A | w/ VSC OFF Switch |
| *B | w/ Headlight Leveling |
Disconnect each connector.
55432B
9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD without Driver Side Knee Airbag)
|
Protective Tape |
Apply protective tape as shown in the illustration.
Detach the 4 clips and 4 claws and remove the lower instrument panel finish panel.
73900
10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
55607
11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Detach the 2 claws and 2 guides and remove the No. 2 instrument panel under cover sub-assembly.
67914B
12.REMOVE FRONT DOOR SCUFF PLATE LH
67913B
13.REMOVE FRONT DOOR SCUFF PLATE RH
62112
14.REMOVE COWL SIDE TRIM BOARD LH
Remove the nut.
Detach the clip and remove the cowl side trim board LH.
62111C
15.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
55950G
16.REMOVE DEFROSTER NOZZLE ASSEMBLY
Disconnect the connector and detach the 2 wire harness clamps.
Detach the 3 claws and remove the defroster nozzle assembly.
55870B
17.REMOVE HEATER TO REGISTER DUCT ASSEMBLY
Remove the 2 clips.
Pull up the heater to register duct assembly to detach the 6 claws and remove it.
18.REMOVE LOWER INSTRUMENT PANEL (for LHD)
Disconnect each connector and detach each wire harness clamp.
Detach the claw and disconnect the hood lock control lever.
Detach the 2 claws and disconnect the DLC3.
Detach the 2 claws and disconnect the cooler thermistor.
| *A | for 4WD/AWD | *B | w/ Power Back Door |
| *C | w/ Downhill Assist Control | *D | w/ Entry and Start System |
Remove the 6 bolts <E> or <F> and 2 bolts <C> or <D>.
Remove the bolt <G> and lower instrument panel.
| *1 | Bolt <E> or <F> | *2 | Bolt <C> or <D> |
| *3 | Bolt <G> | - | - |
19.REMOVE LOWER INSTRUMENT PANEL (for RHD)
Disconnect each connector and detach each wire harness clamp.
Detach the claw and disconnect the hood lock control lever.
Detach the 2 claws and disconnect the DLC3.
Detach the 2 claws and disconnect the cooler thermistor.
| *A | for 4WD/AWD | *B | w/ Power Back Door |
| *C | w/ Downhill Assist Control | *D | w/ Entry and Start System |
Remove the 7 bolts <E> or <F> and 2 bolts <C> or <D>.
Remove the bolt <G> and lower instrument panel.
| *1 | Bolt <E> or <F> | *2 | Bolt <C> or <D> |
| *3 | Bolt <G> | - | - |