Home › Engine / Hybrid System › 1AD-FTV ENGINE MECHANICAL › CYLINDER BLOCK › 2013.11–2015.10
RM3090E _51 Engine / Hybrid System _008733 1AD-FTV ENGINE MECHANICAL _0049237 CYLINDER BLOCK A

1AD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Before performing these installation procedures, sufficiently clean and remove any foreign matter from the cylinder block sub-assembly, connecting rod and other parts.


PROCEDURE

Hide 1.INSTALL CYLINDER BLOCK STUD BOLT

NOTICE:

If a cylinder block stud bolt is deformed or the threads are damaged, replace it.


a.

Apply adhesive to the holes for the stud bolts labeled A on the cylinder block sub-assembly. Install the cylinder block stud bolts labeled A.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Using an E5 "TORX" socket wrench, install the cylinder block stud bolts labeled B and C.

Torque:
for stud bolt B : 3.0 N*m (31 kgf*cm, 27 in.*lbf)
for stud bolt C : 2.0 N*m (20 kgf*cm, 18 in.*lbf)

A298155
0.51,0.24 0.823,0.396 0.313,0.156 10 false *a 4.125,0.26 4.438,0.417 0.313,0.156 10 false *b 1.25,3.26 1.563,3.417 0.313,0.156 10 false *c 1.281,4.51 1.594,4.667 0.313,0.156 10 false *c 2.458,3.917 2.771,4.073 0.313,0.156 10 false *d 1.198,5.979 1.51,6.135 0.313,0.156 10 false *e 1.198,6.979 1.5,7.188 0.302,0.208 10 false *f 2.469,6.417 2.781,6.635 0.313,0.219 10 false *g 4.906,3.76 5.219,3.917 0.313,0.156 10 false *h 4.875,4.292 5.188,4.448 0.313,0.156 10 false *f 6.104,4.021 6.417,4.219 0.313,0.198 10 false *i 0.229,1.021 0.385,1.219 0.156,0.198 10 false A 1.188,1.052 1.344,1.25 0.156,0.198 10 false A 2.396,1.448 2.552,1.646 0.156,0.198 10 false B 5.781,0.979 5.938,1.177 0.156,0.198 10 false C 4.542,0.979 4.698,1.177 0.156,0.198 10 false C 0.719,5 0.875,5.198 0.156,0.198 10 false A 0.698,7.385 0.854,7.583 0.156,0.198 10 false B 4.417,4.948 4.573,5.146 0.156,0.198 10 false C
*a Intake Side *b Exhaust Side
*c 22 mm (0.866 in.) *d 73 mm (2.87 in.)
*e 30 mm (1.18 in.) *f 9 mm (0.354 in.)
*g 49 mm (1.93 in.) *h 12 mm (0.472 in.)
*i 23 mm (0.906 in.) - -



c.
A206565

Apply adhesive to the holes for the stud bolts on the crankshaft bearing cap. Install the 2 cylinder block stud bolts to the crankshaft bearing cap.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 11573 2.INSTALL OIL REFLECTOR PLATE

a.

Using a 5 mm hexagon wrench, install the 3 oil reflector plates with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 19315 4.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A207986
1.126,0.316 1.294,0.479 0.168,0.163 10 *1 2.062,0.734 1.391,0.395 1.391,0.395 1.319,0.395 false
*1 Straight Pin


Install the No. 1 crankshaft position sensor plate by fitting the straight pin of the crankshaft into the hole on the No. 1 crankshaft position sensor plate.


b.

Using a T30 "TORX" socket wrench, install the 3 bolts.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

NOTICE:

Make sure that the No. 1 crankshaft position sensor plate is not slanted.



Hide 13101 5.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A298157
2.51,0.656 2.781,0.385 2.781,0.385 2.927,0.375 false 2.99,0.313 3.302,0.469 0.313,0.156 10 *1
*1 Service Hole


Using a screwdriver, install a new snap ring on one side of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



b.

Gradually heat the piston with pin sub-assembly to approximately 80 to 90°C (176 to 194°F).


c.

Coat the piston pin with engine oil.


d.
A111361
1.009,1.864 1.204,2.039 0.195,0.175 10 *1 1.691,1.722 1.357,1.95 1.357,1.95 1.224,1.95 false 0.769,0.722 0.964,0.897 0.195,0.175 10 *1 1.549,0.383 1.117,0.808 1.117,0.808 0.984,0.808 false
*1 Front Mark


Align the front marks of the piston and connecting rod sub-assembly, install the connecting rod sub-assembly to the piston and push in the piston pin with your thumb.

HINT:

The piston and pin are a matched set.



e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


f.
A111320
3.223,1.379 3.402,1.553 0.179,0.175 10 *1 3.044,1.746 3.151,1.473 3.151,1.473 3.202,1.473 false
*1 Service Hole


Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



Hide 13011 6.INSTALL PISTON RING SET

a.
A111363

Install the oil ring expander by hand.


b.
A111364
2.09,2.317 2.296,2.482 0.206,0.165 10 *1 2.035,3.758 2.217,3.909 0.182,0.151 10 *2 1.729,2.675 1.978,2.405 1.978,2.405 2.073,2.405 false 1.592,4.406 1.872,3.851 1.872,3.851 2.002,3.851 false 1.852,4.405 1.872,3.851 false
*1 Coil Joint
*2 Oil Ring End


Using a piston ring expander, install the oil ring rail.

HINT:

Face the end gap of the oil ring in the opposite direction of the coil joint.



c.
A298158
2.25,1.104 2.479,0.208 2.479,0.208 2.646,0.219 false 1.229,1.281 1.583,0.188 1.583,0.188 1.74,0.188 false 1.833,0.073 2.146,0.229 0.313,0.156 10 *1 2.74,0.115 3.052,0.271 0.313,0.156 10 *2 0.115,1.313 0.427,1.469 0.313,0.156 10 *a
*1 Code Mark (T1)
*2 Code Mark (FTE2 or 2T)
*a Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring so that the code marks are positioned as shown in the illustration.

Code Mark:
Item Code Mark
No. 1 Compression Ring T1
No. 2 Compression Ring FTE2 or 2T


HINT:

Install the No. 1 compression ring and No. 2 compression ring with the code mark facing upward.



d.
A111366
1.204,0.948 1.594,1.114 0.39,0.166 10 *1 0.504,1.029 0.66,1.195 0.156,0.166 10 *5 0.31,1.685 0.512,1.851 0.202,0.166 10 *a 2.636,2.446 2.827,2.612 0.192,0.166 10 *2 1.157,2.45 1.351,2.616 0.194,0.166 10 *3 2.603,0.956 2.786,1.122 0.183,0.166 10 *4 0.715,1.116 0.827,1.116 0.827,1.116 1.309,1.606 false
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring
*4 Coil
*5 Front Mark
*a Front


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the ring ends.



Hide 13041 7.INSTALL CONNECTING ROD BEARING

NOTICE:

Apply oil to the inner surface of each connecting rod bearing (the surface which contacts the crankshaft), but not to the outer surface (the surface which contacts the connecting rod sub-assembly or connecting rod cap).


a.
A298159
1.135,3.135 1.292,3.333 0.156,0.198 10 A 2.156,3.135 2.313,3.333 0.156,0.198 10 B

Install the connecting rod bearings to the connecting rod sub-assembly and connecting rod cap.


b.

Using a vernier caliper, measure the distance between the connecting rod bearing cap edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Clean the backside of the connecting rod bearing and the connecting bearing surface of the connecting rod sub-assembly.



Hide 11711 8.INSTALL CRANKSHAFT BEARING

NOTICE:
·

Apply oil to the inner surface of each crankshaft bearing (the surface which contacts the crankshaft), but not to the outer surface (the surface which contacts the crankshaft bearing cap or cylinder block sub-assembly).

·

When replacing a crankshaft bearing, also replace the corresponding crankshaft bearing or No. 2 crankshaft bearing.



a.

Clean each main journal, crankshaft bearing and No. 2 crankshaft bearing.


b.
A101023

Align the crankshaft bearing claw with the claw groove of the cylinder block sub-assembly, and push in the 5 crankshaft bearings to install them.

NOTICE:
·

Clean the contact surface of the crankshaft bearing and cylinder block sub-assembly.


·

Apply oil to the inner surface of each crankshaft bearing (the surface which contacts the crankshaft), but not to the outer surface (the surface which contacts the cylinder block sub-assembly).


·

Make sure both sides of the oil groove in the cylinder block sub-assembly are visible through the oil feed holes in the crankshaft bearing. Make sure the amount visible on each side of the holes is equal.




c.
A111367
0.53,0.541 0.716,0.71 0.187,0.169 10 *1 1.489,0.627 0.759,0.627 false
*1 Claw


Align the No. 2 crankshaft bearing claw with the claw groove of the crankshaft bearing cap, and push in the 5 No. 2 crankshaft bearings to install them.

NOTICE:
·

Clean the contact surface of the No. 2 crankshaft bearing and crankshaft bearing cap.


·

Apply oil to the inner surface of each No. 2 crankshaft bearing (the surface which contacts the crankshaft), but not to the outer surface (the surface which contacts the crankshaft bearing cap).




Hide 11791 9.INSTALL UPPER CRANKSHAFT THRUST WASHER

NOTICE:

When replacing an upper crankshaft thrust washer, replace both upper crankshaft thrust washers together as a set.


a.

Apply engine oil to the crankshaft bearings, and then place the crankshaft on the cylinder block sub-assembly.


b.
A298160

Push the crankshaft in one direction and install one upper crankshaft thrust washer to the No. 4 journal position with the oil groove facing outward.


c.

Push the crankshaft in the opposite direction and install the other upper crankshaft thrust washer to the No. 4 journal position with the oil groove facing outward.


Hide 13411 10.INSTALL CRANKSHAFT

a.
A111382
1.927,3.302 2.281,3 2.281,3 2.385,3 false 1.063,3.083 1.177,3.083 1.177,3.083 1.51,3.667 false 0.125,2.51 0.573,2.667 0.448,0.156 10 *a 0.844,2.979 1.531,3.146 0.688,0.167 10 *1 2.333,4.031 2.698,4.208 0.365,0.177 10 A - A 1.885,2.354 2.042,2.531 0.156,0.177 10 A 1.885,1.552 2.042,1.729 0.156,0.177 10 A 2.438,2.906 2.667,3.052 0.229,0.146 10 ●
*1 Groove C
*a Front


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

2.0 to 4.0 mm (0.0787 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the crankshaft bearing cap within 3 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after installation.

·

Do not overlap seal packing in area ● in the illustration.

·

Do not apply seal packing in groove C.




b.

Apply engine oil to the crankshaft bearings, and then place the crankshaft bearing cap on the cylinder block sub-assembly.


c.

Install the crankshaft bearing cap bolts.

HINT:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.



d.
A298161
1.667,0.292 1.823,0.49 0.156,0.198 10 1 1.688,1.833 1.844,2.031 0.156,0.198 10 2 1.156,0.292 1.313,0.49 0.156,0.198 10 3 2.25,1.833 2.406,2.031 0.156,0.198 10 4 1.125,1.833 1.281,2.031 0.156,0.198 10 5 2.26,0.281 2.417,0.479 0.156,0.198 10 6 0.604,0.26 0.76,0.458 0.156,0.198 10 7 2.802,1.833 2.958,2.031 0.156,0.198 10 8 0.583,1.813 0.74,2.01 0.156,0.198 10 9 2.75,0.302 3.063,0.5 0.313,0.198 10 10

Step 1:

i.

Uniformly tighten the 10 crankshaft bearing cap bolts in several steps in the sequence shown in the illustration.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)

HINT:

If any of the crankshaft bearing cap bolts does not meet the torque specification, replace the crankshaft bearing cap bolt.




e.

Step 2:

i.

Mark the front of the crankshaft bearing cap bolts with paint.


ii.

Tighten the crankshaft bearing cap bolts by 90°.


iii.

Check that the painted marks are now at a 90° angle to the front.



f.

Check that the crankshaft turns smoothly.


g.
A207984
1.683,0.44 1.804,0.604 0.121,0.163 10 1 1.545,2.633 1.666,2.796 0.121,0.163 10 2 1.133,0.407 1.255,0.571 0.121,0.163 10 3 2.167,2.589 2.289,2.752 0.121,0.163 10 4 1.189,2.633 1.31,2.796 0.121,0.163 10 5 2.227,0.473 2.349,0.637 0.121,0.163 10 6 0.237,0.898 0.359,1.062 0.121,0.163 10 7 3.132,2.253 3.253,2.417 0.121,0.163 10 8 0.237,2.175 0.359,2.338 0.121,0.163 10 9 3.121,0.859 3.307,1.023 0.186,0.163 10 10

Install and uniformly tighten the 10 bolts in several passes in the sequence shown.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 11.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A111366
1.204,0.948 1.594,1.114 0.39,0.166 10 *1 0.504,1.029 0.66,1.195 0.156,0.166 10 *5 0.31,1.685 0.512,1.851 0.202,0.166 10 *a 2.636,2.446 2.827,2.612 0.192,0.166 10 *2 1.157,2.45 1.351,2.616 0.194,0.166 10 *3 2.603,0.956 2.786,1.122 0.183,0.166 10 *4 0.715,1.116 0.827,1.116 0.827,1.116 1.309,1.606 false
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring
*4 Coil
*5 Front Mark
*a Front


Check the positions of the piston ring ends.

NOTICE:

Do not align the ring ends.



c.
A298162
0.833,0.625 1.083,0.135 1.083,0.135 1.198,0.135 false 1.26,0.031 1.573,0.188 0.313,0.156 10 false *1 0.156,0.771 0.469,0.927 0.313,0.156 10 false *a
*1 Front Mark
*a Front


Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.


d.
A129591
1.813,0.74 2.479,0.156 2.479,0.156 2.573,0.156 false 2.625,0.073 2.865,0.219 0.24,0.146 10 *1
*1 Front Mark


Install the connecting rod cap so that its front mark (protrusion) is facing the correct direction.

NOTICE:
·

Make sure that the front mark of the connecting rod cap is facing forward.


·

Match the numbered connecting rod cap with the connecting rod.




e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.
A129592

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


g.

Mark the front side of each connecting cap bolt with paint.


h.

Tighten the cap bolts by 90°.


i.

Check that the painted marks are now at a 90° angle to the front.


j.

Check that the crankshaft turns smoothly.


Hide 12.INSPECT CONNECTING ROD THRUST CLEARANCE