CHECK TELEVISION CAMERA ASSEMBLY
Disconnect the U22 television camera assembly.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| U22-6 (CB+) - Body ground | B - Body ground | Power source | Ignition switch ACC | 5.5 to 7.05 V |
| U22-5 (CGND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the U22 television camera assembly connector.
Check for pulses between each terminal of the connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| U22-3 (CV+) - U22-2 (CV-) | W - R | Video signal | Ignition switch ON, camera lens not covered, displaying an image | Pulse generation (See waveform 1) |
| Ignition switch ON, camera lens covered, blacking out screen | Pulse generation (See waveform 2) |
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected. If the result is not as specified, the television camera assembly may have a malfunction.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| *a | Waveform 1 |
| *b | Waveform 2 |
| *c | Synchronized Signal |
| *d | Video Waveform |
Reference (Oscilloscope waveform):
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Waveform 1
| Item | Content |
|---|---|
| Terminal No. (Symbol) | U22-3 (CV+) - U22-5 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, camera lens not covered, displaying an image |
The video waveform changes according to the image sent by the television camera assembly.
Waveform 2
| Item | Content |
|---|---|
| Terminal No. (Symbol) | U22-3 (CV+) - U22-5 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, camera lens covered, blacking out screen |
The video waveform changes according to the image sent by the television camera assembly.
CHECK NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)
Check for resistance, voltage and waveform between each terminal of the connector.
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected. If the result is not as specified, the television camera assembly may have a malfunction.
| *a | Waveform 1 |
| *b | Waveform 2 |
| *c | Synchronized Signal |
| *d | Video Waveform |
Reference (Oscilloscope waveform):
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.
Waveform
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G158-12 (V+) - G158-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, camera lens covered, blacking out the screen |
The video waveform changes according to the image sent by the television camera assembly.
CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
Check for resistance, voltage and waveform between each terminal of the connector.
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected. If the result is not as specified, the television camera assembly may have a malfunction.
| *a | Waveform 1 |
| *b | Waveform 2 |
| *c | Synchronized Signal |
| *d | Video Waveform |
Reference (Oscilloscope waveform):
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
Waveform
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G159-12 (V+) - G159-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, camera lens covered, blacking out the screen |
The video waveform changes according to the image sent by the television camera assembly.