Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) › from 2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0103549 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the television camera assembly receives a signal via CAN communication from the spiral with sensor cable sub-assembly that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in spiral with sensor cable sub-assembly power source
·

Harness or connector

·

Spiral with sensor cable sub-assembly



WIRING DIAGRAM

E290770
1.073,0.625 2.906,0.823 1.833,0.198 10 false from Battery 0.438,1.177 1.948,1.51 1.51,0.333 10 false from IG1 NO.1 Relay*1 0.448,1.594 1.781,1.99 1.333,0.396 10 false from Engine Stop and Start ECU*2 0.792,3.417 2.625,3.615 1.833,0.198 10 false : CAN Communication Line 0.125,2.667 2.417,2.865 2.292,0.198 10 false *1: w/o Stop and Start System 0.135,3.042 2.427,3.24 2.292,0.198 10 false *2: w/ Stop and Start System 3.25,2.469 4.615,2.896 1.365,0.427 10 false Spiral with Sensor Cable Sub-assembly 5.573,2.208 6.75,2.729 1.177,0.521 10 false Television Camera Assembly 3.396,0.625 5.229,0.823 1.833,0.198 10 false BAT 3.406,1.167 5.24,1.365 1.833,0.198 10 false IG 2.125,1.323 3.958,1.521 1.833,0.198 10 false ECU-IG NO.1 2.135,0.771 3.969,0.969 1.833,0.198 10 false ECU-B NO.1 3.156,0.479 3.708,0.792 0.552,0.313 10 false 5 3.167,1.052 3.719,1.365 0.552,0.313 10 false 4 3.188,1.76 3.74,2.073 0.552,0.313 10 false 1 3.26,2.292 3.813,2.604 0.552,0.313 10 false G12 3.396,1.813 5.229,2.01 1.833,0.198 10 false ESS

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY POWER SOURCE)
a.
E224381C02
1.49,0.156 1.979,0.448 0.49,0.292 2.063,1.521 2.49,1.479 false 1.865,1.563 1.865,1.865 1.865,1.865 2.49,1.865 false 1.427,1.583 1.427,1.885 1.427,1.885 0.802,1.885 false 0.469,1.813 0.885,2.01 0.417,0.198 10 ESS 2.542,1.781 2.958,1.979 0.417,0.198 10 IG 2.531,1.375 2.948,1.573 0.417,0.198 10 BAT 0.208,0.073 0.625,0.271 0.417,0.198 10 *a 1.615,0.219 1.885,0.396 0.271,0.177 10 G12
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


Disconnect the G12 spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G12-4 (IG) - G12-1 (ESS) Ignition switch ON 11 to 14 V
G12-5 (BAT) - G12-1 (ESS) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR