Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2013.11–2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E271826E03
5.667,2.896 6.125,3.094 0.458,0.198 10 false G141 5.698,3.063 6.906,3.458 1.208,0.396 10 false Radio and Display Receiver Assembly 0.417,2.896 0.75,3.094 0.333,0.198 10 false M32 0.427,3.063 1.615,3.5 1.188,0.438 10 false Stereo Component Amplifier Assembly 6,0.552 6.313,0.75 0.313,0.198 10 false FL- 6.021,1.052 6.333,1.25 0.313,0.198 10 false FL+ 6.01,1.5 6.323,1.698 0.313,0.198 10 false FR- 6.01,1.979 6.323,2.177 0.313,0.198 10 false FR+ 1.094,0.552 1.406,0.75 0.313,0.198 10 false L- 1.094,1.042 1.406,1.24 0.313,0.198 10 false L+ 1.094,1.5 1.406,1.698 0.313,0.198 10 false R- 1.083,1.969 1.396,2.167 0.313,0.198 10 false R+ 0.979,2.448 1.438,2.646 0.458,0.198 10 false SLD 2.281,2.604 2.906,2.833 0.625,0.229 10 false Shielded 3.917,2.583 4.552,2.833 0.635,0.25 10 false Shielded 1.417,0.438 1.729,0.635 0.313,0.198 10 false 2 1.417,0.917 1.729,1.115 0.313,0.198 10 false 3 1.417,1.396 1.729,1.594 0.313,0.198 10 false 4 1.417,1.875 1.729,2.073 0.313,0.198 10 false 5 1.417,2.333 1.875,2.531 0.458,0.198 10 false 6 5.75,0.438 6.063,0.635 0.313,0.198 10 false 6 5.75,0.917 6.063,1.115 0.313,0.198 10 false 2 5.75,1.385 6.063,1.583 0.313,0.198 10 false 5 5.76,1.865 6.073,2.063 0.313,0.198 10 false 1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G141 radio and display receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-5 (R+) - G141-1 (FR+) Always Below 1 Ω
M32-4 (R-) - G141-5 (FR-) Always Below 1 Ω
M32-3 (L+) - G141-2 (FL+) Always Below 1 Ω
M32-2 (L-) - G141-6 (FL-) Always Below 1 Ω
M32-6 (SLD) - Body ground Always 10 kΩ or higher
M32-5 (R+) - Body ground Always 10 kΩ or higher
M32-4 (R-) - Body ground Always 10 kΩ or higher
M32-3 (L+) - Body ground Always 10 kΩ or higher
M32-2 (L-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR