The video signal from the television camera assembly is transmitted to the navigation ECU sub-assembly.
When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point.
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Electrical devices are used in the cabin (noise may occur in the image).
Accessories that generate radio waves have been installed (noise may occur in the image).
The outer mirror switch assembly is operated (noise may occur in the image).
The camera lens is frosted over (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The television camera assembly lens is scratched.
The television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.
Disconnect the G49 navigation ECU sub-assembly connector.
Disconnect the U6 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G49-7 (CA+) - U6-6 (CB+) | Always | Below 1 Ω |
| G49-8 (V+) - U6-3 (CV+) | Always | Below 1 Ω |
| G49-16 (V-) - U6-2 (CV-) | Always | Below 1 Ω |
| G49-15 (CGND) - U6-5 (CGND) | Always | Below 1 Ω |
| G49-7 (CA+) - Body ground | Always | 10 kΩ or higher |
| G49-8 (V+) - Body ground | Always | 10 kΩ or higher |
| G49-16 (V-) - Body ground | Always | 10 kΩ or higher |
| G49-15 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation ECU Sub-assembly) |
Reconnect the G49 navigation ECU sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G49-15 (CGND) - Body ground | Always | Below 1 Ω |
| G49-16 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G49-7 (CA+) - G49-15 (CGND) | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the U6 television camera assembly connector.
| *a | Component with harness connected
(Navigation ECU Sub-assembly) |
*b | Waveform 1 (camera lens is not covered, displaying an image) |
| *c | Waveform 2 (camera lens is covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the television camera assembly using an oscilloscope.
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly with the connector connected.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G49-8 (V+) - G138-7 (GND1) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, shift lever in R |
The video waveform changes according to the image sent by the television camera assembly.
| Proceed to |
|---|
| Waveform is as shown in the illustration |
| Waveform is not as shown in the illustration |
Waveform is as shown in the illustration
Waveform is not as shown in the illustration