Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(for Navigation Receiver Type) › 2013.11–2014.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0103548 PARKING ASSIST MONITOR SYSTEM(for Navigation Receiver Type) J

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Navigation Receiver Type)  Guide Lines and Buttons are not Displayed for All Display Modes  


DESCRIPTION

The navigation ECU sub-assembly receives back door open/close signals from the main body ECU (multiplex network body ECU) via CAN communication. When the back door is open, the camera aiming cannot be adjusted correctly because the television camera assembly is installed on the back door. Therefore, when performing back camera position setting while the back door is open, a back door open warning message will be displayed on the screen and back camera position setting will be canceled.

HINT:

Check the parking assist monitor screen display mode settings. (Check if the parking guide lines are set to off.)


WIRING DIAGRAM

E290768E01
0.333,1.688 0.792,1.885 0.458,0.198 10 false U12 0.333,1.854 2.094,2.073 1.76,0.219 10 false Back Door Lock Assembly 0.479,1.302 0.938,1.5 0.458,0.198 10 false ACT- 1.552,1.302 1.833,1.5 0.281,0.198 10 false D+ 0.271,1.188 0.552,1.385 0.281,0.198 10 false 1 1.875,1.219 2.156,1.417 0.281,0.198 10 false 3 2.406,1.219 2.688,1.417 0.281,0.198 10 false 33 4.208,1.198 4.49,1.396 0.281,0.198 10 false 20 4.469,1.344 4.948,1.531 0.479,0.188 10 false BCTY 2.656,1.792 2.938,1.99 0.281,0.198 10 false 3E 2.667,1.969 4.292,2.333 1.625,0.365 10 false Instrument Panel Junction Block Assembly 4.365,2.333 4.646,2.531 0.281,0.198 10 false A 4.354,2.521 5.51,3.094 1.156,0.573 10 false Main Body ECU (Multiplex Network Body ECU) 5.906,2.354 7.063,2.927 1.156,0.573 10 false Navigation ECU Sub-assembly 0.583,3.458 2.552,3.677 1.969,0.219 10 true : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the navigation ECU sub-assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Navigation Receiver Type)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Navigation Receiver Type)>CALIBRATION).



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
-
OK:

The back door courtesy switch functions as specified in the normal condition column.


Body Electrical > Main Body > Data List
Tester Display
Back Door Courtesy SW
50003 123 26

Result:
Proceed to
OK
NG



OK

NG

2.INSPECT BACK DOOR LOCK ASSEMBLY
2.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the U12 back door lock assembly connector.


b.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U12-3 (D+) - A-20 (BCTY) Always Below 1 Ω
U12-3 (D+) - Body ground Always 10 kΩ or higher
U12-1 (ACT-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the U12 back door lock assembly connector.


b.

Disconnect the 3E instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U12-3 (D+) - 3E-33 Always Below 1 Ω
U12-3 (D+) - Body ground Always 10 kΩ or higher
U12-1 (ACT-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR