Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › 2013.11–2016.08
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0104513 NAVIGATION SYSTEM(for SD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.

When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either condition below is met:
·

Stereo component amplifier assembly is/was not connected while the engine switch is on (ACC) or on (IG).

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.


·

Stereo component amplifier assembly

·

Navigation receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition.

·

The navigation receiver assembly is the master unit.



WIRING DIAGRAM

E263055E05
5.229,0.479 5.688,0.677 0.458,0.198 10 false M33 5.229,0.969 5.688,1.167 0.458,0.198 10 false M32 5.24,1.667 5.698,1.865 0.458,0.198 10 false M32 5.229,2.063 5.688,2.26 0.458,0.198 10 false M32 5.229,2.458 5.688,2.656 0.458,0.198 10 false M33 2.958,0.615 3.417,0.813 0.458,0.198 10 false AMP 2.948,1.115 3.406,1.313 0.458,0.198 10 false ACC 0.563,0.448 2.396,0.646 1.833,0.198 10 false from Battery 0.354,0.948 2.5,1.146 2.146,0.198 10 false from ACC Relay 5.313,0.25 5.469,0.448 0.156,0.198 10 false 1 5.281,0.75 5.594,0.948 0.313,0.198 10 false 12 5.323,1.469 5.479,1.667 0.156,0.198 10 false 8 5.333,1.875 5.49,2.073 0.156,0.198 10 false 7 5.323,2.26 5.479,2.458 0.156,0.198 10 false 3 3.198,1.656 3.813,1.854 0.615,0.198 10 false TX1+ 3.229,2.042 3.844,2.24 0.615,0.198 10 false TX1- 3.625,1.563 3.781,1.76 0.156,0.198 10 false 7 3.635,1.938 3.948,2.135 0.313,0.198 10 false 8 2.604,2.594 3.063,2.792 0.458,0.198 10 false G139 2.625,2.771 3.854,3.115 1.229,0.344 10 false Navigation Receiver Assembly 5.479,2.969 6.76,3.375 1.281,0.406 10 false Stereo Component Amplifier Assembly 5.635,0.469 5.948,0.667 0.313,0.198 10 false +B 5.677,0.969 6.135,1.167 0.458,0.198 10 false ACC 5.667,1.667 6.125,1.865 0.458,0.198 10 false TX+ 5.667,2.052 6.125,2.25 0.458,0.198 10 false TX- 5.667,2.458 6.125,2.656 0.458,0.198 10 false GND 0.708,3.417 2.75,3.635 2.042,0.219 10 false : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.


Result:
Result Proceed to
DTC B15C3 is not output A
DTC B15C3 is output B



A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

GO TO DTC "B15C3" IN DIAGNOSTIC TROUBLE CODE CHART

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK FOR DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E271825C03
1.49,0.083 1.906,0.292 0.417,0.208 1.49,1.719 1.906,1.927 0.417,0.208 0.917,2.375 1.094,1.844 true 0.417,1.885 0.573,2.385 true 2.656,0.958 2.896,1.271 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.104 1.875,0.281 0.313,0.177 10 false M32 1.563,1.74 1.875,1.958 0.313,0.219 10 false M33 1.146,1.771 1.49,1.979 0.344,0.208 10 false GND 0.177,1.792 0.417,2.01 0.24,0.219 10 false +B 2.958,1.188 3.313,1.396 0.354,0.208 10 false ACC
*a Front view of wire harness connector (to Stereo Component Amplifier Assembly)


Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-1 (+B) - M33-3 (GND) Always 11 to 14 V
M32-12 (ACC) - M32-3 (GND) Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G139 navigation receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-7 (TX1+) - M32-8 (TX+) Always Below 1 Ω
G139-8 (TX1-) - M32-7 (TX-) Always Below 1 Ω
G139-7 (TX1+) - Body ground Always 10 kΩ or higher
G139-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG