Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2013.11
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0104513 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

The navigation receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

WIRING DIAGRAM

E289275E03
5.76,0.458 5.917,0.656 0.156,0.198 10 false 6 1.365,0.396 1.521,0.594 0.156,0.198 10 false 2 1.365,0.906 1.521,1.104 0.156,0.198 10 false 3 1.365,1.354 1.521,1.552 0.156,0.198 10 false 4 1.365,1.833 1.521,2.031 0.156,0.198 10 false 5 1.385,2.323 1.542,2.521 0.156,0.198 10 false 6 5.76,0.917 5.917,1.115 0.156,0.198 10 false 2 5.76,1.406 5.917,1.604 0.156,0.198 10 false 5 5.75,1.875 5.906,2.073 0.156,0.198 10 false 1 1.135,0.542 1.521,0.76 0.385,0.219 10 false L- 1.094,1.021 1.479,1.24 0.385,0.219 10 false L+ 1.104,1.49 1.49,1.708 0.385,0.219 10 false R- 1.083,1.979 1.646,2.188 0.563,0.208 10 false R+ 0.99,2.448 1.448,2.667 0.458,0.219 10 false SLD 0.271,2.896 0.656,3.115 0.385,0.219 10 false M32 0.281,3.052 2,3.385 1.719,0.333 10 false Stereo Component Amplifier Assembly 5.719,3.042 6.948,3.385 1.229,0.344 10 false Navigation Receiver Assembly 2.26,2.625 2.865,2.792 0.604,0.167 10 false Shielded 3.885,2.604 4.49,2.771 0.604,0.167 10 false Shielded 5.719,2.896 6.438,3.094 0.719,0.198 10 false G137 5.969,0.542 6.354,0.76 0.385,0.219 10 false FL- 5.969,1.031 6.354,1.25 0.385,0.219 10 false FL+ 5.969,1.5 6.354,1.719 0.385,0.219 10 false FR- 5.958,1.979 6.521,2.188 0.563,0.208 10 false FR+

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G137 navigation receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-5 (R+) - G137-1 (FR+) Always Below 1 Ω
M32-4 (R-) - G137-5 (FR-) Always Below 1 Ω
M32-3 (L+) - G137-2 (FL+) Always Below 1 Ω
M32-2 (L-) - G137-6 (FL-) Always Below 1 Ω
M32-6 (SLD) - Body ground Always 10 kΩ or higher
M32-5 (R+) - Body ground Always 10 kΩ or higher
M32-4 (R-) - Body ground Always 10 kΩ or higher
M32-3 (L+) - Body ground Always 10 kΩ or higher
M32-2 (L-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR