Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2013.11–2015.04
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





JUNCTION CONNECTOR


a.

No. 1 CAN Junction Connector

HINT:

Connectors that connect to the No. 1 CAN junction connector can be distinguished by the color of their CAN bus wires. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C253921C26
5.229,2.802 5.438,2.594 5.438,2.594 5.646,2.594 true 5.229,3 5.438,3.271 5.438,3.271 5.646,3.271 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *1 2.01,1.76 2.438,1.917 0.427,0.156 10 false G118 4.25,2.208 4.563,2.365 0.313,0.156 10 false *a 2.021,1.979 2.448,2.135 0.427,0.156 10 false G119 2.021,2.198 2.448,2.354 0.427,0.156 10 false G120 2.021,2.417 2.448,2.573 0.427,0.156 10 false G126 2.021,2.646 2.448,2.802 0.427,0.156 10 false G127 2.021,2.865 2.448,3.021 0.427,0.156 10 false G123 2.021,3.083 2.448,3.24 0.427,0.156 10 false G124 2.021,3.313 2.448,3.469 0.427,0.156 10 false G125 5.677,2.49 6.104,2.646 0.427,0.156 10 false CANH 5.677,3.167 6.104,3.323 0.427,0.156 10 false CANL
*1 No. 1 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
- -


No. 1 CAN Junction Connector Wiring Color Connect to

*: w/ Stop and Start System

G118-1 (CANH) L No. 3 CAN junction connector
G118-2 (CANL) W
G119-1 (CANH) V No. 2 CAN junction connector
G119-2 (CANL) W
G120-1 (CANH) R Brake actuator assembly (skid control ECU)
G120-2 (CANL) W
G123-1 (CANH) Y Main body ECU (multiplex network body ECU)
G123-2 (CANL) W
G124-1 (CANH) B DLC3
G124-2 (CANL) W
G125-1 (CANH) BR Airbag sensor assembly
G125-2 (CANL) W
G126-1 (CANH) G Air conditioning amplifier assembly
G126-2 (CANL) W
G127-1 (CANH) LG Engine stop and start ECU*
G127-2 (CANL) W


b.

No. 2 CAN Junction Connector

HINT:

Connectors that connect to the No. 2 CAN junction connector can be distinguished by the color of their CAN bus wires. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C253921C30
5.229,2.802 5.438,2.594 5.438,2.594 5.646,2.594 true 5.229,3 5.438,3.271 5.438,3.271 5.646,3.271 true 0.052,0.063 0.365,0.219 0.313,0.156 10 false *1 2.021,1.76 2.448,1.917 0.427,0.156 10 false G155 4.25,2.208 4.563,2.365 0.313,0.156 10 false *a 2.031,1.979 2.458,2.135 0.427,0.156 10 false G156 2.021,2.198 2.448,2.354 0.427,0.156 10 false G128 2.021,2.417 2.448,2.573 0.427,0.156 10 false G129 2.021,2.646 2.448,2.802 0.427,0.156 10 false G130 2.021,2.865 2.448,3.021 0.427,0.156 10 false G131 2.01,3.083 2.438,3.24 0.427,0.156 10 false G132 2.021,3.313 2.448,3.469 0.427,0.156 10 false G157 5.677,2.5 6.104,2.656 0.427,0.156 10 false CANH 5.677,3.177 6.104,3.333 0.427,0.156 10 false CANL
*1 No. 2 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
- -


No. 2 CAN Junction Connector Wiring Color Connect to

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System

*3: for 4WD/AWD

*4: w/ Entry and Start System

*5: w/ Lane Departure Alert System

G128-1 (CANH) G Combination meter assembly
G128-2 (CANL) W
G129-1 (CANH) V No. 1 CAN junction connector
G129-2 (CANL) W
G130-1 (CANH) Y
·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2


G130-2 (CANL) W
G131-1 (CANH) L 4WD ECU assembly*3
G131-2 (CANL) W
G132-1 (CANH) R Certification ECU (smart key ECU assembly)*4
G132-2 (CANL) W
G155-1 (CANH) LG Power steering ECU assembly
G155-2 (CANL) W
G156-1 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
G156-2 (CANL) W
G157-1 (CANH) B Lane departure warning camera*5
G157-2 (CANL) W


c.

No. 3 CAN Junction Connector

HINT:

Connectors that connect to the No. 3 CAN junction connector can be distinguished by the color of their CAN bus wires. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C278780C04
5.25,2.833 5.417,2.5 5.417,2.5 5.583,2.5 true 5.25,3 5.417,3.25 5.417,3.25 5.583,3.25 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 2.031,1.76 2.344,1.958 0.313,0.198 10 false N27 5.667,2.417 6.167,2.667 0.5,0.25 10 false CANH 5.667,3.167 6.167,3.417 0.5,0.25 10 false CANL 4.25,2.219 4.563,2.417 0.313,0.198 10 false *a 2.031,1.979 2.344,2.177 0.313,0.198 10 false N28 2.031,2.198 2.344,2.396 0.313,0.198 10 false N29
*1 No. 3 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 3 CAN Junction Connector)
- -


No. 3 CAN Junction Connector Wiring Color Connect to

*: w/ Blind Spot Monitor System

N27-1 (CANH) Y ECM
N27-2 (CANL) W
N28-1 (CANH) L No. 1 CAN junction connector
N28-2 (CANL) W
N29-1 (CANH) R Blind spot monitor sensor LH*
N29-2 (CANL) W


d.

No. 4 CAN Junction Connector (for Power Seat)

C234761C02
3.375,0.521 3.771,0.813 0.396,0.292 3.344,1.417 3.146,0.656 3.146,0.656 2.948,0.656 true 3.219,1.417 2.917,0.854 2.917,0.854 2.688,0.854 true 3.208,1.667 2.958,2.104 2.958,2.104 2.729,2.104 true 3.365,1.667 3.156,2.385 3.156,2.385 2.823,2.385 true 3.448,0.583 3.906,0.781 0.458,0.198 10 N30 0.156,0.146 0.615,0.344 0.458,0.198 10 *a 2.406,0.563 3.021,0.75 0.615,0.188 10 CANH*c 2.208,2.021 2.823,2.208 0.615,0.188 10 CANL*b 2.146,0.781 2.76,0.969 0.615,0.188 10 CANH*b 2.302,2.302 2.917,2.49 0.615,0.188 10 CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b for Main Body ECU (Multiplex Network Body ECU)
*c for No. 5 CAN Junction Connector - -


No. 4 CAN Junction Connector Wiring Color Connect to
N30-1 (CANH) B Main body ECU (multiplex network body ECU)
N30-7 (CANL) W
N30-2 (CANH) V No. 5 CAN junction connector
N30-8 (CANL) W


e.

No. 5 CAN Junction Connector (w/ Power Back Door System)

C235392C33
4.417,1.25 4.833,1.5 0.417,0.25 3.365,1.292 2.917,0.667 2.917,0.667 2.667,0.667 true 3.26,1.313 2.813,0.865 2.813,0.865 2.583,0.865 true 3.177,1.313 2.833,1.083 2.833,1.083 2.583,1.083 true 3.177,1.469 2.833,1.75 2.833,1.75 2.583,1.75 true 3.271,1.479 2.927,1.906 2.927,1.906 2.677,1.906 true 3.365,1.49 3.115,2.156 3.115,2.156 2.865,2.156 true 3.458,1.479 3.26,2.406 3.26,2.406 3.01,2.406 true 3.458,1.313 2.948,0.438 2.948,0.438 2.719,0.438 true 2.156,0.302 3.073,0.5 0.917,0.198 10 false CANH*b 0.083,0.052 1,0.25 0.917,0.198 10 false *a 2.115,0.542 3.031,0.74 0.917,0.198 10 false CANH*c 2.031,0.75 2.948,0.948 0.917,0.198 10 false CANH*d 2.333,2.042 3.25,2.24 0.917,0.198 10 false CANL*c 2.115,1.813 3.031,2.01 0.917,0.198 10 false CANL*d 2.458,2.313 3.375,2.51 0.917,0.198 10 false CANL*b 4.5,1.302 5.417,1.5 0.917,0.198 10 false N32 2.021,0.979 2.938,1.177 0.917,0.198 10 false CANH*e 2.063,1.646 2.979,1.844 0.917,0.198 10 false CANL*e
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b for Television Camera Assembly (w/ Parking Assist Monitor System [for Camera built-in ECU])
*c for Multiplex Network Door ECU *d for No. 1 CAN Junction Terminal
*e
·

for No. 4 CAN Junction Connector (for Power Seat)

·

for Main Body ECU (Multiplex Network Body ECU) (except Power Seat)


- -


No. 5 CAN Junction Connector Wiring Color Connect to

*1: w/ Parking Assist Monitor System (for Camera built-in ECU)

*2: for Power Seat

*3: except Power Seat

N32-7 (CANH) P Television camera assembly*1
N32-18 (CANL) W
N32-8 (CANH) G Multiplex network door ECU
N32-19 (CANL) W
N32-9 (CANH) L No. 1 CAN junction terminal
N32-20 (CANL) W
N32-10 (CANH) V*2, B*3
·

No. 4 CAN junction connector*2

·

Main body ECU (multiplex network body ECU)*3


N32-21 (CANL) W


f.
C210060C17
0.271,0.969 0.688,1.219 0.417,0.25 1.646,0.219 1.5,0.219 1.5,0.219 1.354,0.885 true 2.167,0.458 2.021,0.458 2.021,0.458 1.719,0.885 true 1.688,0.135 2.25,0.313 0.563,0.177 10 CANH*b 0.354,1.021 0.656,1.198 0.302,0.177 10 N31 2.219,0.375 2.781,0.552 0.563,0.177 10 CANL*b 0.156,0.115 0.719,0.292 0.563,0.177 10 *a
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b for No. 5 CAN Junction Connector


No. 1 CAN Junction Terminal (w/ Power Back Door System)

No. 1 CAN Junction Terminal Wiring Color Connect to
N31-2 (CANL) W No. 5 CAN junction connector
N31-3 (CANH) L



CHECK DLC3


a.
C253362C06
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.052 0.708,1.25 0.458,0.198 10 G14 0.75,0.417 1.208,0.615 0.458,0.198 10 CG 2.469,0.344 2.927,0.542 0.458,0.198 10 CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G14-6 (CANH) - G14-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G14-6 (CANH) - G14-4 (CG) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-14 (CANL) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G14-6 (CANH) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G14-14 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


a.

for 2AR-FE:

C228683E02
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 4.781,1.031 4.448,0.365 4.448,0.365 4.229,0.365 true 4.781,1.135 4.479,0.604 4.479,0.604 4.24,0.604 true 2.667,1.042 2.365,0.51 2.365,0.51 2.125,0.51 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B77 3.823,0.292 4.5,0.5 0.677,0.208 10 CANH 3.865,0.542 4.542,0.75 0.677,0.208 10 CANL 1.906,0.438 2.365,0.635 0.458,0.198 10 E1 6.76,0.521 7.156,0.677 0.396,0.156 10 BATT

i.

Disconnect the ECM connectors.

C229008C05
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.604,1.448 2.948,2.115 2.948,2.115 3.135,2.115 true 2.594,1.365 2.885,0.927 2.885,0.927 3.094,0.927 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.344,0.844 0.75,1.083 0.406,0.24 10 BATT 3.135,0.844 3.635,1.094 0.5,0.25 10 CANH 1.729,0.552 2.135,0.792 0.406,0.24 10 A62 4.063,0.667 4.469,0.906 0.406,0.24 10 E1 4.833,0.625 5.24,0.865 0.406,0.24 10 B77 3.156,2.042 3.656,2.292 0.5,0.25 10 CANL
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B77-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B77-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.

for 3ZR-FAE or 3ZR-FE:

C228683C02
5.281,0.26 5.74,0.51 0.458,0.25 2.438,0.24 2.896,0.49 0.458,0.25 4.781,1.031 4.448,0.365 4.448,0.365 4.229,0.365 true 4.781,1.135 4.479,0.604 4.479,0.604 4.24,0.604 true 2.667,1.042 2.365,0.51 2.365,0.51 2.125,0.51 true 6.125,1.031 6.469,0.604 6.469,0.604 6.719,0.604 true 4.135,1.229 3.802,2.177 3.802,2.177 3.479,2.177 true 4.24,1.24 4.042,2.385 4.042,2.385 3.74,2.385 true 4.896,1.031 4.594,0.167 4.594,0.167 4.313,0.167 true 4.885,1.146 5.188,2.24 5.188,2.24 5.469,2.24 true 5.375,0.302 5.833,0.5 0.458,0.198 10 A62 2.552,0.292 3.01,0.49 0.458,0.198 10 B75 3.646,0.292 4.323,0.5 0.677,0.208 10 CANH*A 3.708,0.521 4.385,0.729 0.677,0.208 10 CANL*A 1.906,0.438 2.365,0.635 0.458,0.198 10 E1 6.76,0.521 7.156,0.677 0.396,0.156 10 BATT 2.969,2.104 3.646,2.313 0.677,0.208 10 CAN-*B 3.198,2.313 3.875,2.521 0.677,0.208 10 CAN+*B 3.729,0.094 4.406,0.302 0.677,0.208 10 CANP*C 5.5,2.167 6.177,2.375 0.677,0.208 10 CANN*C
*A V Bus *B Sub Bus 15
*C Local Bus - -


i.

Disconnect the ECM connectors.

C229008C06
1.656,0.51 2.073,0.76 0.417,0.25 4.771,0.583 5.188,0.833 0.417,0.25 1.438,1.396 1,0.917 1,0.917 0.75,0.917 true 2.604,1.448 2.948,2.115 2.948,2.115 3.135,2.115 true 2.594,1.365 2.885,0.927 2.885,0.927 3.094,0.927 true 4.844,1.406 4.417,0.75 4.417,0.75 4.26,0.75 true 3.771,1.563 4.208,2.469 4.208,2.469 4.542,2.469 true 3.823,1.563 4.396,2.208 4.396,2.208 4.729,2.208 true 2.521,1.375 2.792,0.646 2.792,0.646 3,0.646 true 2.542,1.469 2.844,2.417 2.844,2.417 3.031,2.417 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.344,0.844 0.75,1.083 0.406,0.24 10 BATT 3.135,0.844 3.708,1.094 0.573,0.25 10 CANH*A 1.729,0.552 2.135,0.792 0.406,0.24 10 A62 4.063,0.667 4.469,0.906 0.406,0.24 10 E1 4.854,0.625 5.26,0.865 0.406,0.24 10 B75 3.156,2.042 3.781,2.292 0.625,0.25 10 CANL*A 4.75,2.104 5.375,2.354 0.625,0.25 10 CAN-*B 4.573,2.385 5.219,2.615 0.646,0.229 10 CAN+*B 3.031,0.583 3.604,0.833 0.573,0.25 10 CANP*C 3.073,2.354 3.698,2.604 0.625,0.25 10 CANN*C
*A V Bus *B Sub Bus 15
*C Local Bus - -
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-13 (CANH) - B75-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-26 (CANL) - B75-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 15
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B75-61 (CAN+) - B75-62 (CAN-) Y - L HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B75-61 (CAN+) - B75-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B75-62 (CAN-) - B75-16 (E1) L - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B75-61 (CAN+) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B75-62 (CAN-) - A62-1 (BATT) L - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-12 (CANP) - A62-25 (CANN) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A62-12 (CANP) - B75-16 (E1) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-25 (CANN) - B75-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A62-12 (CANP) - A62-1 (BATT) B - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A62-25 (CANN) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



c.

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF:

C159489C01
2.344,0.385 2.76,0.656 0.417,0.271 4.781,0.458 5.198,0.729 0.417,0.271 5.094,1.073 5.563,0.469 5.563,0.469 5.729,0.469 true 5.479,1.125 6.146,1.969 6.146,1.969 6.313,1.969 true 5.354,1.104 5.844,2.448 5.844,2.448 6.094,2.448 true 5.781,1.188 6.229,1.438 6.229,1.438 6.417,1.438 true 2.094,1.24 1.354,0.635 1.354,0.635 1.125,0.635 true 2.094,1.365 1.563,2.521 1.563,2.521 1.302,2.521 true 5.24,1.073 5.75,0.667 5.75,0.667 5.917,0.667 true 1.219,1.99 1,2.156 1,2.156 0.74,2.156 true 4.854,0.521 5.323,0.719 0.469,0.198 10 false A61 2.438,0.438 2.906,0.635 0.469,0.198 10 false B76 5.948,0.615 6.646,0.813 0.698,0.198 10 false CANL*A 5.771,0.417 6.469,0.615 0.698,0.198 10 false CANH*A 6.146,2.333 6.844,2.531 0.698,0.198 10 false CANP*C 6.365,1.854 7.063,2.052 0.698,0.198 10 false CANN*C 6.479,1.365 7.021,1.563 0.542,0.198 10 false BATT 0.542,2.063 1.083,2.26 0.542,0.198 10 false E1 0.563,0.573 1.26,0.771 0.698,0.198 10 false CAN+*B 0.781,2.448 1.479,2.646 0.698,0.198 10 false CAN-*B
*A V Bus *B Sub Bus 15
*C Local Bus - -


i.

Disconnect the ECM connectors.

C234869C03
0.323,1.354 0.792,1.625 0.469,0.271 5.094,0.479 5.563,0.75 0.469,0.271 1.573,0.604 1.833,0.604 1.833,0.604 2.156,1.188 true 1.458,0.833 1.677,0.833 1.677,0.833 1.958,1.188 true 4.479,0.688 4.74,0.688 4.74,0.688 5.083,1.292 true 2.771,0.729 2.635,0.729 2.635,0.729 2.427,1.198 true 6.125,2.188 5.823,2.188 5.823,2.188 5.667,1.813 true 4.51,2.25 4.76,2.25 4.76,2.25 5.094,1.396 true 2.708,0.427 2.573,0.427 2.573,0.427 2.344,1.208 true 1.708,0.354 1.969,0.354 1.969,0.354 2.26,1.188 true 0.427,1.427 0.719,1.604 0.292,0.177 10 A61 0.125,0.073 0.417,0.25 0.292,0.177 10 *a 1.115,0.76 1.542,0.927 0.427,0.167 10 BATT 2.823,0.667 3.688,0.833 0.865,0.167 10 CANH*A 3.938,2.177 4.802,2.344 0.865,0.167 10 CAN-*B 6.177,2.104 7.042,2.271 0.865,0.167 10 E1 5.198,0.552 5.531,0.729 0.333,0.177 10 B76 2.75,0.375 3.615,0.542 0.865,0.167 10 CANL*A 1.125,0.302 1.99,0.469 0.865,0.167 10 CANP*C 0.99,0.531 1.854,0.698 0.865,0.167 10 CANN*C 3.906,0.625 4.771,0.792 0.865,0.167 10 CAN+*B
*A V Bus *B Sub Bus 15
*C Local Bus - -
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-7 (CANH) - A61-6 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A61-7 (CANH) - B76-109 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-6 (CANL) - B76-109 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-7 (CANH) - A61-2 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A61-6 (CANL) - A61-2 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 15
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B76-40 (CAN+) - B76-63 (CAN-) Y - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B76-40 (CAN+) - B76-109 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B76-63 (CAN-) - B76-109 (E1) B - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B76-40 (CAN+) - A61-2 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B76-63 (CAN-) - A61-2 (BATT) B - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Local Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-5 (CANP) - A61-4 (CANN) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A61-5 (CANP) - B76-109 (E1) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-4 (CANN) - B76-109 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A61-5 (CANP) - A61-2 (BATT) B - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A61-4 (CANN) - A61-2 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


C278790C01
2.51,5.542 2.927,5.792 0.417,0.25 1.333,7.385 1.75,7.635 0.417,0.25 3.333,7.385 3.75,7.635 0.417,0.25 1.302,3.656 1.719,3.906 0.417,0.25 3.875,5.792 4.167,6.25 4.167,6.25 4.333,6.25 true 3.167,6.198 3.417,6.198 3.417,6.198 3.781,5.781 true 3.49,8.188 3.833,8.583 3.833,8.583 4,8.583 true 3,8.583 3.167,8.583 3.167,8.583 3.396,8.177 true 1.271,8.583 1.438,8.583 1.438,8.583 1.667,8.177 true 1.771,8.156 2.052,7.583 2.052,7.583 2.219,7.583 true 1.25,4.844 1.5,4.844 false 1.25,7.042 1.5,7.042 false 2.417,3.417 2.583,3.417 2.583,3.417 3,3.781 true 5.333,3.417 5.167,3.417 5.167,3.417 4.771,3.771 true 0.25,4.26 0.917,4.417 0.667,0.156 10 *A 0.25,6.604 0.563,6.76 0.313,0.156 10 *B 2.604,6.115 3.25,6.354 0.646,0.24 10 CANH*C 2.25,7.51 2.833,7.833 0.583,0.323 10 CANP*D 1.083,4.76 1.396,4.917 0.313,0.156 10 *1 4.396,6.167 5.042,6.406 0.646,0.24 10 CANL*C 0.708,8.5 1.375,8.74 0.667,0.24 10 CANN*D 2.583,5.583 2.896,5.74 0.313,0.156 10 G78 3.417,7.427 3.729,7.583 0.313,0.156 10 G78 4.063,8.51 4.708,8.75 0.646,0.24 10 CANL*C 2.438,8.5 3.083,8.75 0.646,0.25 10 CANH*C 1.406,7.427 1.719,7.583 0.313,0.156 10 G79 1.073,6.969 1.385,7.125 0.313,0.156 10 *1 1.469,3.698 2.135,3.854 0.667,0.156 10 A 2,3.344 2.646,3.583 0.646,0.24 10 GND1 5.417,3.344 6.063,3.583 0.646,0.24 10 BECU 2.667,1.667 3.333,1.823 0.667,0.156 10 A
*A Main body ECU (multiplex network body ECU) with 1 connector *B Main body ECU (multiplex network body ECU) with 3 connectors
*C V Bus *D Sub Bus 1
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

C279368C01
5.385,0.385 5.771,0.656 0.385,0.271 2.26,0.333 2.646,0.604 0.385,0.271 0.073,0.292 0.458,0.563 0.385,0.271 4.938,0.771 5.083,0.771 5.083,0.771 5.281,1.021 true 6.313,0.771 6.458,0.771 6.458,0.771 6.656,1.021 true 0.979,0.948 1.333,1.438 1.333,1.438 1.531,1.438 true 0.927,0.948 1.219,1.625 1.219,1.625 1.417,1.625 true 3.292,0.958 3.646,1.448 3.646,1.448 3.844,1.448 true 3.25,0.969 3.542,1.646 3.542,1.646 3.74,1.646 true 1.448,1.552 2.104,1.771 0.656,0.219 10 CANH*A 3.875,1.354 4.521,1.594 0.646,0.24 10 CANP*B 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 4.271,0.094 4.583,0.25 0.313,0.156 10 *b 3.771,1.563 4.458,1.771 0.688,0.208 10 CANN*B 1.563,1.354 2.156,1.677 0.594,0.323 10 CANL*A 4.542,0.688 5.188,0.927 0.646,0.24 10 GND1 5.917,0.698 6.563,0.938 0.646,0.24 10 BECU 5.531,0.438 5.844,0.594 0.313,0.156 10 A 2.333,0.375 2.74,0.646 0.406,0.271 10 G79 0.146,0.344 0.552,0.615 0.406,0.271 10 G78
*A V Bus *B Sub Bus 1
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G78-14 (CANH) - G78-13 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G78-14 (CANH) - A-11 (GND1) Y - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-13 (CANL) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G78-14 (CANH) - A-30 (BECU) Y - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G78-13 (CANL) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G79-9 (CANP) - G79-10 (CANN) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G79-9 (CANP) - A-11 (GND1) B - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-10 (CANN) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G79-9 (CANP) - A-30 (BECU) B - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G79-10 (CANN) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


E161130E26
3.344,0.26 3.823,0.542 0.479,0.281 4.719,1.208 4.885,1.563 4.885,1.563 4.969,1.563 true 2.438,1.229 2.188,1.427 2.188,1.427 2.063,1.427 true 3.375,1.208 3.146,1.646 3.146,1.646 3.021,1.646 true 3.51,1.208 3.698,1.615 3.698,1.615 3.885,1.615 true 3.438,0.323 3.719,0.49 0.281,0.167 10 G16 5.01,1.479 5.271,1.667 0.26,0.188 10 ET 1.906,1.344 2.042,1.531 0.135,0.188 10 B 2.604,1.563 3.021,1.729 0.417,0.167 10 CANH 3.927,1.531 4.354,1.688 0.427,0.156 10 CANL

a.
C240157C07
1.531,0.146 1.969,0.458 0.438,0.313 1.719,1.219 2.26,1.76 2.26,1.76 2.49,1.76 true 1.635,1.219 1.375,1.844 1.375,1.844 1.135,1.844 true 0.979,1.219 0.781,1.083 0.781,1.083 0.604,1.083 true 2.865,1.448 2.708,1.448 2.708,1.448 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 1.625,0.229 2.083,0.427 0.458,0.198 10 G16 0.719,1.75 1.177,1.948 0.458,0.198 10 CANH 2.531,1.667 3.01,1.865 0.479,0.198 10 CANL 2.917,1.385 3.219,1.656 0.302,0.271 10 ET 0.49,1.021 0.854,1.281 0.365,0.26 10 B
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G16-32 (CANH) - G16-21 (ET) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-31 (CANL) - G16-21 (ET) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G16-32 (CANH) - G16-40 (B) G - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G16-31 (CANL) - G16-40 (B) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


C123353E68
2.604,0.698 2.969,0.927 0.365,0.229 2.302,2.344 2.479,2.344 2.479,2.344 2.813,2 true 3.167,1.594 3.625,0.802 3.625,0.802 3.844,0.802 true 3.333,2.042 3.573,2.323 3.573,2.323 3.792,2.323 true 2.646,0.729 3,0.958 0.354,0.229 10 G92 3.896,0.74 4.427,1.063 0.531,0.323 10 CANH 2.021,2.281 2.479,2.531 0.458,0.25 10 E1 3.833,2.25 4.292,2.5 0.458,0.25 10 CANL

a.
C227529C03
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 *a 0.198,2.083 0.51,2.24 0.313,0.156 10 *b 0.438,2.573 0.781,2.781 0.344,0.208 10 G14 0.417,1 0.76,1.208 0.344,0.208 10 G92 2.75,0.583 3.292,0.792 0.542,0.208 10 CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 BAT 1,1.604 1.542,1.813 0.542,0.208 10 E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G92-13 (CANH) - G92-22 (CANL) BR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G92-13 (CANH) - G92-25 (E1) BR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-22 (CANL) - G92-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G92-13 (CANH) - G14-16 (BAT) BR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G92-22 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


C197053E19
1.531,0.083 1.969,0.344 0.438,0.26 2.344,1.604 2.635,1.844 2.635,1.844 2.802,1.844 true 2.365,1.375 1.781,2.031 1.781,2.031 2.031,2.031 true 2.583,0.896 2.781,0.552 2.781,0.552 2.948,0.552 true 0.833,1.479 0.656,1.813 0.656,1.813 0.479,1.813 true 1.615,0.125 1.927,0.292 0.313,0.167 10 A64 2.865,1.75 3.333,1.927 0.469,0.177 10 CANH 2.094,1.938 2.563,2.115 0.469,0.177 10 CANL 2.99,0.479 3.406,0.646 0.417,0.167 10 GND1 0.229,1.729 1.24,1.896 1.01,0.167 10 BM

a.
C234968C29
1.5,0.125 1.979,0.417 0.479,0.292 2.927,1.969 2.698,1.969 2.698,1.969 2.448,1.354 true 0.833,0.25 1.073,0.25 1.073,0.25 1.469,1.26 true 0.833,2 1.125,2 1.125,2 1.469,1.365 true 0.479,0.792 0.76,0.792 0.76,0.792 1.135,1.073 true 1.615,0.198 1.948,0.427 0.333,0.229 10 A64 0.083,0.073 0.344,0.229 0.26,0.156 10 *a 2.958,1.896 3.385,2.094 0.427,0.198 10 BM 0.073,0.729 0.479,0.896 0.406,0.167 10 GND1 0.417,1.938 0.823,2.104 0.406,0.167 10 CANH 0.417,0.177 0.823,0.344 0.406,0.167 10 CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A64-25 (CANH) - A64-14 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A64-25 (CANH) - A64-1 (GND1) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-14 (CANL) - A64-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A64-25 (CANH) - A64-24 (BM) R - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A64-14 (CANL) - A64-24 (BM) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C228050E03
1.458,0.365 1.885,0.646 0.427,0.281 1.906,1.354 2.188,1.719 2.188,1.719 2.5,1.719 true 1.74,1.354 1.563,1.844 1.563,1.844 1.281,1.844 true 2.125,1.313 2.458,0.99 2.458,0.99 2.771,0.99 true 1.323,1.333 1.021,1.031 1.021,1.031 0.74,1.031 true 1.531,0.427 1.854,0.615 0.323,0.188 10 G12 2.833,0.896 3.24,1.052 0.406,0.156 10 ESS 2.552,1.635 3.052,1.844 0.5,0.208 10 CANL 0.875,1.76 1.375,1.969 0.5,0.208 10 CANH 0.438,0.958 0.938,1.167 0.5,0.208 10 BAT

a.
C277459C04
1.521,0.188 1.938,0.438 0.417,0.25 1.094,1.844 1.344,1.844 1.344,1.844 1.521,1.396 true 2.563,0.875 2.333,0.875 2.333,0.875 2.115,1.24 true 2.24,1.844 1.99,1.844 1.99,1.844 1.75,1.396 true 0.771,0.906 1.021,0.906 1.021,0.906 1.344,1.219 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 2.625,0.781 3.104,0.938 0.479,0.156 10 false BAT 0.458,0.823 0.938,0.979 0.479,0.156 10 false ESS 1.594,0.219 2.073,0.375 0.479,0.156 10 false G12 2.302,1.75 2.781,1.906 0.479,0.156 10 false CANH 0.688,1.76 1.167,1.917 0.479,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G12-3 (CANH) - G12-2 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G12-3 (CANH) - G12-1 (ESS) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-2 (CANL) - G12-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G12-3 (CANH) - G12-5 (BAT) P - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G12-2 (CANL) - G12-5 (BAT) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


B264892E76
4.719,0.646 5.167,0.927 0.448,0.281 1.854,0.646 2.302,0.927 0.448,0.281 3.135,2.323 2.823,2.323 2.823,2.323 2.51,1.646 true 4.281,2.177 4.563,2.177 4.563,2.177 4.823,1.5 true 1.146,0.833 1.344,0.833 1.344,0.833 1.552,1.344 true 4.083,0.906 4.365,0.906 4.365,0.906 4.729,1.479 true 4.813,0.698 5.271,0.896 0.458,0.198 10 G84 3.646,0.823 4.104,1.021 0.458,0.198 10 CANL 3.833,2.094 4.292,2.292 0.458,0.198 10 CANH 0.938,0.771 1.396,0.969 0.458,0.198 10 +B 3.208,2.24 3.667,2.438 0.458,0.198 10 E 1.938,0.708 2.396,0.906 0.458,0.198 10 G82

a.
C277455C02
0.115,2.396 0.521,2.677 0.406,0.281 0.292,0.677 0.698,0.958 0.406,0.281 0.771,1.406 0.99,1.406 0.99,1.406 1.135,1.083 true 2.292,0.781 2.542,0.552 2.542,0.552 2.75,0.552 true 2.667,1.875 2.427,1.875 2.427,1.875 2.094,2.552 true 2.552,1.604 2.313,1.604 2.313,1.604 1.969,2.542 true 0.052,0.031 0.365,0.188 0.313,0.156 10 *a 0.354,0.74 0.667,0.896 0.313,0.156 10 G82 0.177,2.448 0.49,2.604 0.313,0.156 10 G84 0.615,1.323 0.927,1.479 0.313,0.156 10 E 2.802,0.469 3.115,0.625 0.313,0.156 10 +B 2.719,1.802 3.167,2.031 0.448,0.229 10 CANL 2.604,1.542 3.052,1.771 0.448,0.229 10 CANH
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G84-14 (CANH) - G84-15 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G84-14 (CANH) - G82-11 (E) R - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-15 (CANL) - G82-11 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G84-14 (CANH) - G82-2 (+B) R - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G84-15 (CANL) - G82-2 (+B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])


C297912E01
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 4.99,0.802 5.292,1.333 5.292,1.333 5.458,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.479,0.177 2.094,0.375 0.615,0.198 10 false G141 4.979,0.146 5.594,0.344 0.615,0.198 10 false G143 5.5,1.229 6.115,1.427 0.615,0.198 10 false CANH 4.042,1.26 4.656,1.458 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C04
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.51,0.302 1.969,0.5 0.458,0.198 10 false G141 1.542,1.885 2,2.083 0.458,0.198 10 false G143 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G143-9 (CANH) - G141-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-10 (CANL) - G141-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G143-9 (CANH) - G141-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G143-10 (CANL) - G141-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


C297912E05
4.917,0.094 5.385,0.385 0.469,0.292 1.417,0.125 1.885,0.417 0.469,0.292 0.896,0.469 1.052,0.469 1.052,0.469 1.26,0.698 true 1.729,0.927 1.99,1.292 1.99,1.292 2.156,1.292 true 5,0.802 5.302,1.333 5.302,1.333 5.469,1.333 true 4.448,1.375 4.594,1.375 4.594,1.375 4.885,0.802 true 1.479,0.177 2.094,0.375 0.615,0.198 10 false G137 4.979,0.156 5.594,0.354 0.615,0.198 10 false G139 5.521,1.229 6.135,1.427 0.615,0.198 10 false CANH 4.042,1.271 4.656,1.469 0.615,0.198 10 false CANL 2.208,1.188 2.823,1.385 0.615,0.198 10 false GND1 0.594,0.365 1.208,0.563 0.615,0.198 10 false +B1

a.
C277477C05
1.5,0.24 1.938,0.479 0.438,0.24 1.469,1.833 1.906,2.073 0.438,0.24 2.146,1.594 1.896,1.594 1.896,1.594 1.677,1.125 true 2.635,0.719 2.385,0.719 2.385,0.719 2.188,0.875 true 2.5,3.135 2.25,3.135 2.25,3.135 2.031,2.667 true 1.896,2.646 1.688,3.177 1.688,3.177 1.438,3.177 true 2.198,1.51 2.74,1.74 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.542,0.281 2,0.479 0.458,0.198 10 false G137 1.51,1.865 1.969,2.063 0.458,0.198 10 false G139 2.677,0.625 3.219,0.854 0.542,0.229 10 false +B1 2.552,3.063 3.094,3.292 0.542,0.229 10 false CANL 1.031,3.083 1.573,3.313 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G139-9 (CANH) - G139-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G139-9 (CANH) - G137-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G139-10 (CANL) - G137-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G139-9 (CANH) - G137-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G139-10 (CANL) - G137-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK 4WD ECU ASSEMBLY (for 4WD/AWD)


C270073E03
3.385,0.135 3.813,0.438 0.427,0.302 4.667,1.531 5.146,2.646 5.146,2.646 5.385,2.646 true 4.865,1.531 5.344,2.396 5.344,2.396 5.552,2.396 true 1.677,0.313 1.906,0.313 1.906,0.313 2.427,1.156 true 3.469,0.208 3.938,0.375 0.469,0.167 10 G86 5.594,2.323 6.063,2.49 0.469,0.167 10 CANL 5.438,2.563 5.906,2.729 0.469,0.167 10 CANH 1.344,0.25 1.813,0.417 0.469,0.167 10 GND

a.
C251150C05
0.417,2.51 0.823,2.792 0.406,0.281 0.438,0.927 0.844,1.208 0.406,0.281 2.208,2.833 2.417,3.021 2.417,3.021 2.594,3.021 true 2.229,1.094 2.438,1.281 2.438,1.281 2.615,1.281 true 2.167,1.094 2.333,1.563 2.333,1.563 2.51,1.563 true 0.875,0.688 1.094,0.688 1.094,0.688 1.229,0.948 true 0.083,0.094 0.396,0.25 0.313,0.156 10 *a 0.104,2.083 0.417,2.24 0.313,0.156 10 *b 0.479,2.563 0.854,2.771 0.375,0.208 10 G14 2.656,2.938 3.031,3.146 0.375,0.208 10 BAT 2.563,1.49 3.042,1.76 0.479,0.271 10 CANH 2.667,1.198 3.146,1.469 0.479,0.271 10 CANL 0.51,0.99 0.885,1.198 0.375,0.208 10 G86 0.552,0.635 1.031,0.906 0.479,0.271 10 GND
*a Rear view of wire harness connector
(to 4WD ECU Assembly)
*b Front view of DLC3


Disconnect the 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G86-6 (CANH) - G86-4 (GND) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-5 (CANL) - G86-4 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G86-6 (CANH) - G14-16 (BAT) L - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G86-5 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)


A295480E03
1.563,0.417 1.896,0.667 0.333,0.25 5,0.417 5.333,0.667 0.333,0.25 1.813,1.604 2.094,2.094 2.094,2.094 2.271,2.094 true 1.604,1.604 1.375,2.073 1.375,2.073 1.167,2.073 true 5.802,1.542 6.083,2.031 6.083,2.031 6.26,2.031 true 5.688,1.573 5.458,2.042 5.458,2.042 5.25,2.042 true 1.615,0.469 1.927,0.667 0.313,0.198 10 A65 5.052,0.469 5.365,0.667 0.313,0.198 10 G87 0.833,2.021 1.229,2.25 0.396,0.229 10 GND 2.344,2.031 2.74,2.26 0.396,0.229 10 BIN 6.313,1.958 6.813,2.188 0.5,0.229 10 CANH 4.844,1.979 5.344,2.208 0.5,0.229 10 CANL

a.
C277467C02
0.333,2.25 0.75,2.5 0.417,0.25 0.417,0.667 0.833,0.917 0.417,0.25 2.698,2.844 2.479,2.844 2.479,2.844 2.177,2.521 true 2.354,1.281 2.146,1.281 2.146,1.281 1.865,0.938 true 1.156,1.396 1.375,1.396 1.375,1.396 1.583,0.958 true 2.604,3.135 2.323,3.135 2.323,3.135 2.104,2.521 true 0.167,0.094 0.479,0.25 0.313,0.156 10 *a 0.49,0.719 0.802,0.875 0.313,0.156 10 A65 0.417,2.302 0.729,2.458 0.313,0.156 10 G87 2.396,1.198 2.708,1.354 0.313,0.156 10 BIN 0.823,1.323 1.208,1.49 0.385,0.167 10 GND 2.729,2.781 3.177,2.969 0.448,0.188 10 CANH 2.635,3.052 3.073,3.25 0.438,0.198 10 CANL
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G87-15 (CANH) - G87-16 (CANL) LG - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G87-15 (CANH) - A65-8 (GND) LG - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G87-16 (CANL) - A65-8 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G87-15 (CANH) - A65-7 (BIN) LG - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G87-16 (CANL) - A65-7 (BIN) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


a.

for Automatic Air Conditioning System:

C278749E01
3.375,0.25 3.854,0.542 0.479,0.292 2.417,0.25 2.75,0.25 2.75,0.25 3.375,1.417 true 2.167,0.5 2.5,0.5 2.5,0.5 3.25,1.406 true 4.365,1.521 5.063,2.417 5.063,2.417 5.417,2.417 true 2.083,2.417 2.417,2.417 2.417,2.417 3.083,1.406 true 3.49,0.333 3.948,0.531 0.458,0.198 10 G81 1.771,0.427 2.333,0.667 0.563,0.24 10 CANL 1.75,2.333 2.208,2.531 0.458,0.198 10 GND 2,0.177 2.563,0.417 0.563,0.24 10 CANH 5.479,2.333 5.938,2.531 0.458,0.198 10 B

i.
C240157C06
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.333,1.052 0.792,1.25 0.458,0.198 10 G81 2.333,0.406 2.792,0.604 0.458,0.198 10 CANH 2.25,0.156 2.708,0.354 0.458,0.198 10 CANL 3.031,1.531 3.333,1.802 0.302,0.271 10 B 0.667,0.385 1.031,0.646 0.365,0.26 10 GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G81-11 (CANH) - G81-12 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G81-11 (CANH) - G81-14 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-12 (CANL) - G81-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G81-11 (CANH) - G81-21 (B) G - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G81-12 (CANL) - G81-21 (B) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



b.

for Manual Air Conditioning System:

E219842E04
3.396,0.208 3.813,0.469 0.417,0.26 1.969,0.438 2.198,0.438 2.198,0.438 2.615,0.865 true 2.333,0.229 2.563,0.229 2.563,0.229 2.76,0.844 true 2.229,1.354 2.396,1.354 2.396,1.354 2.698,1.031 true 3.469,0.26 3.927,0.458 0.458,0.198 10 G80 1.896,0.146 2.375,0.344 0.479,0.198 10 CANH 1.573,0.354 2.052,0.552 0.479,0.198 10 CANL 1.896,1.271 2.375,1.469 0.479,0.198 10 GND

i.
C279367C01
1.479,0.167 1.906,0.406 0.427,0.24 0.385,2.563 0.813,2.802 0.427,0.24 2.594,3.073 2.396,3.073 2.396,3.073 2.208,2.813 true 1.094,1.021 0.896,0.76 0.896,0.76 0.708,0.76 true 1.177,1.01 0.969,0.49 0.969,0.49 0.781,0.49 true 1.135,1.135 0.927,1.5 0.927,1.5 0.74,1.5 true 0.073,0.052 0.385,0.208 0.313,0.156 10 *a 0.115,1.948 0.427,2.104 0.313,0.156 10 *b 0.458,2.594 0.854,2.813 0.396,0.219 10 G14 1.552,0.208 1.948,0.427 0.396,0.219 10 G80 2.656,2.99 3.052,3.208 0.396,0.219 10 BAT 0.396,1.406 0.792,1.625 0.396,0.219 10 GND 0.333,0.677 0.802,0.896 0.469,0.219 10 CANL 0.365,0.406 0.833,0.625 0.469,0.219 10 CANH
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G80-8 (CANH) - G80-9 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G80-8 (CANH) - G80-23 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-9 (CANL) - G80-23 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-8 (CANH) - G14-16 (BAT) G - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-9 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK POWER STEERING ECU ASSEMBLY


C239855E06
3.781,1.781 4.188,2.021 0.406,0.24 3.656,0.271 4.063,0.51 0.406,0.24 1.854,0.896 2.188,1.094 0.333,0.198 0.896,1.323 1.229,1.521 0.333,0.198 2.021,0.896 2.021,0.781 false 1.042,1.313 1.042,1.135 true 3.385,2.406 3.594,2.406 3.594,2.406 3.823,2.573 true 3.406,3.125 3.615,3.125 3.615,3.125 3.844,2.729 true 3.156,1.563 3.375,1.563 3.375,1.563 3.563,1.052 true 4.698,1.521 4.438,1.521 4.438,1.521 4.198,1.052 true 0.969,1.344 1.281,1.542 0.313,0.198 10 h1 1.938,0.917 2.25,1.115 0.313,0.198 10 h2 3.771,0.313 4.083,0.51 0.313,0.198 10 h2 3.917,1.833 4.229,2.031 0.313,0.198 10 h1 2.948,2.344 3.5,2.521 0.552,0.177 10 CANH 2.979,3.052 3.531,3.229 0.552,0.177 10 CANL 2.729,1.49 3.281,1.667 0.552,0.177 10 PGND 4.75,1.448 5.302,1.625 0.552,0.177 10 PIG

a.
C279366C01
0.354,2.479 0.719,2.74 0.365,0.26 0.458,0.969 0.823,1.229 0.365,0.26 1.969,0.938 2.25,0.74 2.25,0.74 2.469,0.74 true 1.969,1.25 2.208,1.521 2.208,1.521 2.427,1.521 true 2.156,2.615 2.438,2.417 2.438,2.417 2.656,2.417 true 0.844,2.271 1.094,2.271 1.094,2.271 1.323,2.542 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.563,1.01 0.875,1.167 0.313,0.156 10 h1 0.469,2.531 0.781,2.688 0.313,0.156 10 h2 2.521,0.646 3.01,0.854 0.49,0.208 10 CANH 2.469,1.427 2.958,1.635 0.49,0.208 10 CANL 2.708,2.333 3.198,2.542 0.49,0.208 10 PGND 0.573,2.188 1.063,2.396 0.49,0.208 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
h1-4 (CANH) - h2-2 (PGND) W - R HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-8 (CANL) - h2-2 (PGND) B - R LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
h1-4 (CANH) - h2-1 (PIG) W - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
h1-8 (CANL) - h2-1 (PIG) B - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


C270135C01
1.479,0.177 1.875,0.438 0.396,0.26 2.604,0.583 2.417,0.583 2.417,0.583 2.146,1.01 true 2.479,0.375 2.24,0.375 2.24,0.375 1.948,1 true 1.281,1.354 0.917,1.844 0.917,1.844 0.729,1.844 true 2.531,1.688 2.344,1.688 2.344,1.688 2.198,1.333 true 2.344,1.927 2.135,1.927 2.135,1.927 1.938,1.333 true 1.594,0.219 1.906,0.417 0.313,0.198 10 R1 2.635,0.5 3.24,0.813 0.604,0.313 10 CA2P*B 2.521,0.302 3.125,0.615 0.604,0.313 10 CA1P*A 2.625,1.625 3.229,1.938 0.604,0.313 10 CA2N*B 2.375,1.865 3.042,2.125 0.667,0.26 10 CA1N*A 0.333,1.76 0.938,2.073 0.604,0.313 10 BLGD
*A V Bus
*B Sensor Bus


a.
C268298C03
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 1.448,1.063 1.188,0.719 1.188,0.719 0.958,0.719 true 1.458,1.188 1.198,1.531 1.198,1.531 0.969,1.531 true 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.583,1.208 1.344,1.813 1.344,1.813 1.115,1.813 true 1.563,1.063 1.219,0.448 1.219,0.448 0.99,0.448 true 1.927,1.198 2.135,1.604 2.135,1.604 2.385,1.604 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 0.427,0.646 1.042,0.927 0.615,0.281 10 CA2P*B 0.594,1.74 1.208,1.948 0.615,0.208 10 CA1N*A 2.573,3.156 3.063,3.354 0.49,0.198 10 BAT 1.573,0.292 1.969,0.469 0.396,0.177 10 R1 1.604,2 2,2.177 0.396,0.177 10 G14 0.438,0.396 1.052,0.677 0.615,0.281 10 CA1P*A 0.417,1.458 1.042,1.75 0.625,0.292 10 CA2N*B 2.448,1.51 2.938,1.708 0.49,0.198 10 BLGD
*A V Bus
*B Sensor Bus
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R1-2 (CA1P) - R1-7 (CA1N) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R1-2 (CA1P) - R1-10 (BLGD) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-7 (CA1N) - R1-10 (BLGD) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-2 (CA1P) - G14-16 (BAT) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R1-7 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sensor Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R1-1 (CA2P) - R1-6 (CA2N) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
R1-1 (CA2P) - R1-10 (BLGD) W - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-6 (CA2N) - R1-10 (BLGD) B - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
R1-1 (CA2P) - G14-16 (BAT) W - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R1-6 (CA2N) - G14-16 (BAT) B - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)


C270135E01
1.479,0.177 1.875,0.438 0.396,0.26 2.604,0.583 2.417,0.583 2.417,0.583 2.146,1.01 true 1.281,1.354 0.917,1.844 0.917,1.844 0.729,1.844 true 2.531,1.688 2.344,1.688 2.344,1.688 2.198,1.333 true 1.604,0.219 1.917,0.417 0.313,0.198 10 T1 2.635,0.5 3.24,0.813 0.604,0.313 10 CA2P 2.625,1.625 3.229,1.938 0.604,0.313 10 CA2N 0.333,1.76 0.938,2.073 0.604,0.313 10 BRGB

a.
C268298C04
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.438,1.219 1.281,1.635 1.281,1.635 1.052,1.635 true 1.438,1.063 1.156,0.646 1.156,0.646 0.938,0.646 true 1.927,1.198 2.135,1.604 2.135,1.604 2.385,1.604 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 2.573,3.156 3.063,3.354 0.49,0.198 10 BAT 1.573,0.292 1.969,0.469 0.396,0.177 10 T1 1.604,2 2,2.177 0.396,0.177 10 G14 0.563,0.573 1.177,0.854 0.615,0.281 10 CA2P 0.667,1.552 1.292,1.844 0.625,0.292 10 CA2N 2.448,1.51 2.938,1.708 0.49,0.198 10 BRGB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)
*b Front view of DLC3


Disconnect the blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T1-1 (CA2P) - T1-6 (CA2N) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
T1-1 (CA2P) - T1-10 (BRGB) W - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
T1-6 (CA2N) - T1-10 (BRGB) B - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
T1-1 (CA2P) - G14-16 (BAT) W - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T1-6 (CA2N) - G14-16 (BAT) B - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)


C279365E01
1.5,0.26 1.927,0.542 0.427,0.281 0.802,0.771 0.938,0.771 0.938,0.771 1.229,1.167 true 0.875,1.885 1.021,1.885 1.021,1.885 1.24,1.531 true 1.448,1.563 1.667,1.927 1.667,1.927 1.833,1.927 true 1.583,0.313 2.042,0.51 0.458,0.198 10 Q13 0.417,0.708 0.875,0.906 0.458,0.198 10 CA1P 0.448,1.792 0.906,1.99 0.458,0.198 10 CA1N 1.865,1.854 2.323,2.052 0.458,0.198 10 GND

a.
C267485C03
0.563,1.063 0.99,1.344 0.427,0.281 0.396,2.542 0.823,2.823 0.427,0.281 2.198,2.917 2.344,3.125 2.344,3.125 2.563,3.125 true 2.073,1.406 2.219,1.615 2.219,1.615 2.438,1.615 true 2.063,1.135 2.208,0.958 2.208,0.958 2.427,0.958 true 1.927,1.406 2.208,1.896 2.208,1.896 2.427,1.896 true 0.083,0.083 0.396,0.25 0.313,0.167 10 *a 0.167,2.094 0.479,2.25 0.313,0.156 10 *b 2.615,3.052 2.969,3.24 0.354,0.188 10 BAT 0.469,2.615 0.823,2.802 0.354,0.188 10 G14 0.635,1.115 0.99,1.302 0.354,0.188 10 Q13 2.5,1.531 2.969,1.719 0.469,0.188 10 CA1N 2.5,0.885 2.969,1.073 0.469,0.188 10 CA1P 2.469,1.813 2.938,2 0.469,0.188 10 GND
*a Front view of wire harness connector
(to Lane Departure Warning Camera)
*b Front view of DLC3


Disconnect the lane departure warning camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q13-6 (CA1P) - Q13-12 (CA1N) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q13-6 (CA1P) - Q13-11 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-12 (CA1N) - Q13-11 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q13-6 (CA1P) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q13-12 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


C278778E01
2.417,0.531 2.833,0.781 0.417,0.25 4.302,0.51 4.719,0.76 0.417,0.25 5.635,2.094 5.448,2.094 5.448,2.094 5.094,1.615 true 5.479,2.354 5.292,2.354 5.292,2.354 5.042,1.594 true 3.219,2.094 3,2.094 3,2.094 2.646,1.51 true 2.125,2.094 2.344,2.094 2.344,2.094 2.542,1.5 true 2.5,0.583 2.958,0.781 0.458,0.198 10 U19 4.375,0.552 4.833,0.75 0.458,0.198 10 U18 5.688,2.031 6.146,2.229 0.458,0.198 10 CANP 5.531,2.281 5.99,2.479 0.458,0.198 10 CANN 3.271,2.021 3.729,2.219 0.458,0.198 10 GND 1.958,2.021 2.417,2.219 0.458,0.198 10 B

a.
C278775C02
0.542,2.375 0.938,2.625 0.396,0.25 0.375,0.885 0.771,1.135 0.396,0.25 2.333,1.063 2.448,1.25 2.448,1.25 2.615,1.25 true 2.229,1.063 2.385,1.479 2.385,1.479 2.604,1.479 true 1.667,2.583 1.417,3 1.417,3 1.25,3 true 1.833,2.583 2.021,2.917 2.021,2.917 2.188,2.917 true 0.094,0.073 0.406,0.229 0.313,0.156 10 *a 0.448,0.927 0.802,1.135 0.354,0.208 10 U18 0.615,2.417 0.969,2.625 0.354,0.208 10 U19 2.656,1.417 3.115,1.677 0.458,0.26 10 CANN 2.677,1.167 3.198,1.417 0.521,0.25 10 CANP 2.25,2.833 2.771,3.083 0.521,0.25 10 GND 1.135,2.917 1.656,3.167 0.521,0.25 10 B
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U18-13 (CANP) - U18-14 (CANN) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
U18-13 (CANP) - U19-7 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U18-14 (CANN) - U19-7 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U18-13 (CANP) - U19-8 (B) G - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
U18-14 (CANN) - U19-8 (B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System [for Camera built-in ECU])


C297925E01
1.479,0.229 1.917,0.51 0.438,0.281 1.99,1.063 2.365,0.771 2.365,0.771 2.552,0.771 true 1.99,1.448 2.313,1.74 2.313,1.74 2.5,1.74 true 1.125,1.813 1.375,1.813 1.375,1.813 1.698,1.438 true 1.573,0.271 2.031,0.469 0.458,0.198 10 false U22 2.573,1.635 3.031,1.833 0.458,0.198 10 false CANH 2.625,0.677 3.083,0.875 0.458,0.198 10 false CANL 0.677,1.688 1.135,1.885 0.458,0.198 10 false CGND

a.
C297924C01
2.583,0.969 3.021,1.271 0.438,0.302 0.406,2.542 0.844,2.844 0.438,0.302 2.594,3.104 2.396,3.104 2.396,3.104 2.188,2.865 true 2.177,1.875 1.979,1.875 1.979,1.875 1.719,1.406 true 1.427,1.385 1.01,1.813 1.01,1.813 0.792,1.813 true 1.479,1 0.927,0.521 0.927,0.521 0.708,0.521 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.104,1.969 0.417,2.125 0.313,0.156 10 false *b 0.49,2.573 0.802,2.729 0.313,0.156 10 false G14 2.677,1.01 3,1.229 0.323,0.219 10 false U22 2.229,1.75 2.917,2.083 0.688,0.333 10 false CGND 0.365,1.708 1.052,2.042 0.688,0.333 10 false CANH 0.292,0.417 0.979,0.75 0.688,0.333 10 false CANL 2.656,2.99 3.344,3.323 0.688,0.333 10 false BAT
*a Front view of wire harness connector
(to Television Camera Assembly)
*b Front view of DLC3


Disconnect the television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U22-4 (CANH) - U22-1 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
U22-4 (CANH) - U22-5 (CGND) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U22-1 (CANL) - U22-5 (CGND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
U22-4 (CANH) - G14-16 (BAT) P - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
U22-1 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for 2AD-FHV, 2AD-CCo and Automatic Transaxle)


C278747E01
4.115,0.688 4.552,0.958 0.438,0.271 3.813,1.771 3.229,0.906 3.229,0.906 2.938,0.906 true 3.969,1.771 3.531,0.615 3.531,0.615 3.24,0.615 true 5.083,1.802 5.75,1.073 5.75,1.073 6.135,1.073 true 4.635,1.771 5.135,0.781 5.135,0.781 5.51,0.781 true 4.208,0.75 4.667,0.948 0.458,0.198 10 false B79 5.573,0.719 6.115,0.917 0.542,0.198 10 false BATT 6.208,0.99 6.75,1.188 0.542,0.198 10 false E1 2.542,0.802 3.083,1 0.542,0.198 10 false CAN- 2.792,0.51 3.333,0.708 0.542,0.198 10 false CAN+

a.
C279362C01
1.521,0.313 1.958,0.583 0.438,0.271 1.073,1.271 0.604,0.823 0.604,0.823 0.375,0.823 true 1.479,1.26 1.01,0.604 1.01,0.604 0.75,0.604 true 2.198,1.26 2.5,0.604 2.5,0.604 2.708,0.604 true 2.083,1.271 2.365,0.375 2.365,0.375 2.625,0.375 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 2.771,0.5 3.24,0.719 0.469,0.219 10 false CAN- 2.677,0.281 3.146,0.5 0.469,0.219 10 false CAN+ 0.385,0.521 0.854,0.74 0.469,0.219 10 false BATT 0.156,0.75 0.625,0.969 0.469,0.219 10 false E1 1.615,0.365 2.083,0.583 0.469,0.219 10 false B79
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


Disconnect the transmission control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B79-6 (CAN+) - B79-7 (CAN-) Y - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B79-6 (CAN+) - B79-8 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B79-7 (CAN-) - B79-8 (E1) B - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B79-6 (CAN+) - B79-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B79-7 (CAN-) - B79-1 (BATT) B - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY (for 3ZR-FAE)


C279363E01
1.51,0.135 1.917,0.385 0.406,0.25 1.51,0.865 1.25,0.656 1.25,0.656 1.01,0.656 true 1.521,1.292 1.271,1.604 1.271,1.604 1.031,1.604 true 0.594,1.521 1.208,1.719 0.615,0.198 10 CAN+ 0.635,0.563 1.25,0.76 0.615,0.198 10 CAN- 1.583,0.177 2.198,0.375 0.615,0.198 10 B46

a.
C279364C01
0.302,2.51 0.75,2.792 0.448,0.281 0.406,0.969 0.854,1.25 0.448,0.281 2.563,0.75 2.281,0.75 2.281,0.75 1.885,1.031 true 2.573,1.656 2.292,1.656 2.292,1.656 1.875,1.302 false 2.781,3.104 2.5,3.104 2.5,3.104 2.271,2.844 true 1.625,2.365 1.385,2.021 1.385,2.021 1.156,2.021 true 0.104,0.063 0.417,0.26 0.313,0.198 10 *a 0.104,1.833 0.417,2.031 0.313,0.198 10 *b 0.385,2.563 0.771,2.823 0.385,0.26 10 G14 0.896,1.927 1.281,2.188 0.385,0.26 10 CG 2.823,3.021 3.208,3.281 0.385,0.26 10 BAT 2.615,1.563 3.094,1.833 0.479,0.271 10 CAN+ 2.604,0.677 3.083,0.948 0.479,0.271 10 CAN- 0.49,1.031 0.875,1.292 0.385,0.26 10 B46
*a Front view of wire harness connector
(to Continuously Variable Valve Lift Controller Assembly)
*b Front view of DLC3


Disconnect the continuously variable valve lift controller assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
B46-4 (CAN+) - B46-2 (CAN-) Y - L HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B46-4 (CAN+) - G14-4 (CG) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B46-2 (CAN-) - G14-4 (CG) L - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
B46-4 (CAN+) - G14-16 (BAT) Y - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B46-2 (CAN-) - G14-16 (BAT) L - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BATTERY CURRENT SENSOR ASSEMBLY (for 3ZR-FAE, 1AD-FTV)


C270135E02
1.479,0.177 1.875,0.438 0.396,0.26 2.417,0.583 2.229,0.583 2.229,0.583 1.958,1.01 true 1.656,1.021 1.073,0.625 1.073,0.625 0.885,0.625 true 1.563,0.219 1.875,0.417 0.313,0.198 10 A58 2.479,0.5 3.083,0.813 0.604,0.313 10 CA3N 0.5,0.563 1.104,0.875 0.604,0.313 10 CA3P

a.
C268298C05
1.531,1.948 1.948,2.208 0.417,0.26 1.469,0.24 1.885,0.5 0.417,0.26 2.198,2.938 2.292,3.219 2.292,3.219 2.542,3.219 true 1.677,1.052 1.219,0.479 1.219,0.479 0.969,0.479 true 1.573,1.042 1.198,0.854 1.198,0.854 0.979,0.854 true 1.073,2.167 1.323,2.167 1.323,2.167 1.646,2.521 true 0.073,0.083 0.385,0.24 0.313,0.156 10 *a 0.104,1.979 0.417,2.135 0.313,0.156 10 *b 2.573,3.156 3.063,3.354 0.49,0.198 10 BAT 1.542,0.292 1.938,0.469 0.396,0.177 10 A58 1.604,2 2,2.177 0.396,0.177 10 G14 0.542,0.802 1.156,1.083 0.615,0.281 10 CA3N 0.573,0.417 1.198,0.708 0.625,0.292 10 CA3P 0.781,2.083 1.271,2.281 0.49,0.198 10 CG
*a Front view of wire harness connector
(to Battery Current Sensor Assembly)
*b Front view of DLC3


Disconnect the battery current sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-3 (CA3P) - A58-2 (CA3N) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A58-3 (CA3P) - G14-4 (CG) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-2 (CA3N) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A58-3 (CA3P) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A58-2 (CA3N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher