Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2013.11–2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Stereo Component Amplifier Power Source Circuit  


WIRING DIAGRAM

This circuit provides power to the stereo component amplifier assembly.

WIRING DIAGRAM

E289278E02
0.354,0.521 2.188,0.719 1.833,0.198 10 false from Battery 0.135,1.313 1.969,1.51 1.833,0.198 10 false from ACC Relay 2.708,0.719 3.146,0.885 0.438,0.167 10 false AMP 2.719,1.531 3.156,1.698 0.438,0.167 10 false ACC 5,0.542 5.438,0.708 0.438,0.167 10 false M33 5.01,1.333 5.448,1.5 0.438,0.167 10 false M32 5.01,2.208 5.448,2.375 0.438,0.167 10 false M33 5.104,1.979 5.542,2.146 0.438,0.167 10 false 3 5.052,1.135 5.49,1.302 0.438,0.167 10 false 12 5.073,0.333 5.51,0.5 0.438,0.167 10 false 1 5.354,0.552 5.906,0.719 0.552,0.167 10 false +B 5.385,1.333 5.938,1.5 0.552,0.167 10 false ACC 5.375,2.229 5.927,2.396 0.552,0.167 10 false GND 4.979,2.823 6.75,3.198 1.771,0.375 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E271825C02
1.49,0.052 2,0.302 0.51,0.25 1.844,1.74 2.354,2 0.51,0.26 0.896,2.365 1,1.917 1,1.917 1.25,1.917 true 0.365,1.979 0.531,1.979 0.531,1.979 0.604,2.365 true 2.635,0.885 2.75,0.417 2.75,0.417 3,0.417 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.615,0.094 1.927,0.271 0.313,0.177 10 false M32 1.969,1.792 2.281,2.01 0.313,0.219 10 false M33 1.292,1.833 1.635,2.042 0.344,0.208 10 false GND 0.135,1.896 0.375,2.115 0.24,0.219 10 false +B 3.042,0.333 3.396,0.542 0.354,0.208 10 false ACC
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-1 (+B) - Body ground Always 11 to 14 V
M32-12 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR