Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2013.11–2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


*1: for LHD

*2: for RHD


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Trouble Codes.


f.

According to the display on the GTS, display the Freeze Frame Data for the selected DTC.

Body Electrical > Blind Spot Monitor Master
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) OFF or ON ON: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on
OFF: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) off
-
Warning Indicator Turning on(Master) State of the outer rear view mirror indicator LH turning on OFF or ON OFF: The following conditions are not met
ON: All of the following conditions are met
·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Left turn signal: off

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated


-
Warning Indicator Flashing(Master) State of the outer rear view mirror indicator LH flashing OFF or ON OFF: The following conditions are not met
ON: All of the following conditions are met
·

Not during initial check

·

Vehicle detected in left hand side warning area

·

Left turn signal: on

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated


-
Main Switch Indicator Status State of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) OFF or ON OFF: Indicator not illuminated
ON: Indicator illuminated
-
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Main Switch Indicator Input Circuit Voltage Blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) voltage Min.: 0 V, Max.: 25.5 V Always: 9 to 16 V -
Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC Number of DTCs Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-
Body Electrical > Blind Spot Monitor Slave
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator RH turning on OFF or ON OFF: The following conditions are not met
ON: All of the following conditions are met
·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Right turn signal: OFF

·

Vehicle speed 40 km/h (25 mph) or more

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated


-
Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator RH flashing OFF or ON OFF: The following conditions are not met
ON: All of the following conditions are met
·

Not during initial check

·

Vehicle detected in right hand side warning area

·

Vehicle speed 40 km/h (25 mph) or more

·

Right turn signal: ON

·

Shift lever in any position except R

·

Blind spot monitor warning light not illuminated


-
Buzzer Sound Status State of the rear cross traffic alert buzzer (blind spot monitor buzzer) OFF or ON OFF: Buzzer not sounding
ON: All of the following conditions are met:
·

Not during initial check

·

Vehicle detected in warning area of rear cross traffic alert

·

Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more

·

Shift lever in R

·

No DTC output


w/ RCTA
Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V
-
Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Buzzer Input Circuit Voltage Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Not sounding buzzer: 11 to 14 V Sounding buzzer: Alternating between 0 to 14 V w/ RCTA
Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) Left ON, Right ON or OFF Left ON: Left side of turn signal light switch on
Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off
-
Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Reverse (Only for MT) State of the shift position R signal OFF or ON ON: Shift lever in R
OFF: Shift lever in any position except R
-
Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5° Left turn: Increases
Right turn: Decreases
-
Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC Number of DTCs Min.: 0, Max.: 255 When system is normal: 0
When a malfunction is detected: More than 0
-


CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on.

*1: for LHD

*2: for RHD



d.

Turn the GTS on.


e.

Clear the DTCs and Freeze Frame Data.