This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1622 | Open or Short Circuit in Back Camera Signal | Open or Short Circuit in rear television camera signal | ·
Harness or connector ·
Rear television camera assembly ·
Navigation receiver assembly |
Clear the DTCs.
Check for DTCs.
| Proceed to |
|---|
| No DTC is output |
| DTC is output |
No DTC is output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC is output
Disconnect the G158 navigation receiver assembly connector.
Disconnect the U6 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G158-11 (CA+) - U6-6 (CB+) | Always | Below 1 Ω |
| G158-12 (V+) - U6-3 (CV+) | Always | Below 1 Ω |
| G158-24 (V-) - U6-2 (CV-) | Always | Below 1 Ω |
| G158-23 (CGND) - U6-5 (CGND) | Always | Below 1 Ω |
| G158-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| G158-12 (V+) - Body ground | Always | 10 kΩ or higher |
| G158-24 (V-) - Body ground | Always | 10 kΩ or higher |
| G158-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G158-23 (CGND) - Body ground | Always | Below 1 Ω |
| G158-24 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G158-11 (CA+) - Body ground | Ignition switch ON | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the waveform of the rear television camera assembly using an oscilloscope.
| *a | Component with harness connected
(Navigation Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.
Waveform is as shown in the illustration.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G158-12 (V+) - G158-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, camera lens is not covered, displaying an image
Waveform 2: Ignition switch ON, camera lens is covered, blacking out the screen |
The video waveform changes according to the image sent by the rear television camera assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Replace the rear television camera assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Rear)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Proceed to |
|---|
| No DTC is output |
| DTC is output |
No DTC is output
DTC is output