Home › Power Source / Network › 3ZR-FE BATTERY / CHARGING › GENERATOR(for 100 A Type) › from 2013.11
RM3090E _57 Power Source / Network _008412 3ZR-FE BATTERY / CHARGING _0046987 GENERATOR(for 100 A Type) A

3ZR-FE BATTERY / CHARGING  GENERATOR(for 100 A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A282616N01
1.219,1.25 0.51,0.729 0.51,0.729 1.313,1.042 true 0.198,0.646 0.656,0.844 0.458,0.198 10 SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A264635C03
1.979,0.521 2.104,0.521 2.104,0.521 2.729,0.865 true 2.146,1.979 2.271,1.979 2.271,1.979 2.719,1.344 true 1.792,0.448 2.104,0.604 0.313,0.156 10 false *a 1.958,1.906 2.271,2.063 0.313,0.156 10 false *b
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor to the generator drive end frame.


Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.

Install a new generator bearing cover packing to the generator coil assembly.

NOTICE:

Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A282140C03
0.667,0.281 0.885,0.281 0.885,0.281 1.26,0.688 true 2.823,0.49 3,0.229 3,0.229 3.135,0.229 true 0.479,0.208 0.792,0.365 0.313,0.156 10 false *a 3.177,0.146 3.417,0.344 0.24,0.198 10 false *a
*a Deep Socket Wrench (21 mm)


Using a 21 mm deep socket wrench and press, slowly press in the generator coil.


b.

Install the generator coil with the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A158992C21
1.021,0.708 1.448,0.177 1.448,0.177 1.604,0.177 false 1.646,0.104 1.958,0.26 0.313,0.156 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A153391C05
1.75,0.74 2.177,0.24 2.177,0.24 2.438,0.24 true 2.469,0.167 2.781,0.323 0.313,0.156 10 false *a
*a Pin


Install the generator brush holder to the generator coil with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder.


Hide 27387 6.INSTALL TERMINAL INSULATOR

a.
A296804

Install the terminal insulator to the generator coil.

NOTICE:

Make sure that the terminal insulator is installed with the correct orientation.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 8.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator in a vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch by hand.


c.
A282141C02
1.156,1.375 1.156,0.802 true 1.375,1.896 1.573,1.896 1.573,1.896 2.188,1.208 true 0.406,0.781 1.135,0.156 1.135,0.156 1.396,0.156 true 1.146,0.167 1.781,0.969 true 1.073,1.406 1.385,1.563 0.313,0.156 10 *1 1.448,0.073 2.104,0.292 0.656,0.219 10 SST A 0.906,1.813 1.375,2 0.469,0.188 10 SST B
*1 Rotor Shaft


Install SST A and B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



d.
A302703C03
0.76,1.042 1.125,1.042 false 0.969,0.49 1.156,0.49 1.156,0.49 1.49,0.844 true 0.271,0.948 0.74,1.135 0.469,0.188 10 false SST A 0.479,0.396 0.948,0.583 0.469,0.188 10 false SST B 1.292,2.615 1.49,2.823 0.198,0.208 10 false *a 1.99,2.438 2.188,2.646 0.198,0.208 10 false *b
*a Hold
*b Fulcrum Length
V100135

Turn


Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

Torque:
without SST : 80 N*m (816 kgf*cm, 59 ft.*lbf)
with SST : 64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Be careful as the generator pulley with clutch or rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Make sure SST and the wrench are connected in a straight line.




e.

Remove SST from the generator.


f.

Check that the generator pulley with clutch rotates smoothly.


Hide 27416 9.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.