Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2013.11–2014.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Check for DTCs, and then write them down.


f.

Check the details of the DTC(s).

Body Electrical > Navigation System > Trouble Codes
50001 212


CLEAR DTC (CLEAR USING GTS)


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212


START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.



a.

Start the engine.


b.
E291554

While pressing and holding the "INFO" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.


c.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



FAILURE DIAGNOSIS


a.
E225789

The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.



SYSTEM CHECK


a.
E267332

The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E267333N01
0.521,0.552 0.323,0.552 true 1.146,0.646 1.146,1.708 true 2.063,1.594 2.063,1.792 true 2.646,1.594 2.646,1.792 true 3.073,0.875 2.875,0.875 true 0.146,0.458 0.333,0.667 0.188,0.208 10 *a 1.094,1.771 1.25,1.979 0.156,0.208 10 *b 1.979,1.771 2.167,1.979 0.188,0.208 10 *c 2.563,1.781 2.75,1.99 0.188,0.208 10 *d 3.115,0.781 3.302,0.99 0.188,0.208 10 *e

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 1 are shown in the following table.


*b: Check Result Result codes for all devices are displayed.
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared.

·

Press the "Memory CLR" switch for 3 seconds.


*d: Recheck
·

A system check will be performed again after the memory is cleared.

·

The "Recheck" switch will dim during a system check.


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the navigation system.

·

The names of the components from Device Name List No. 2 are shown in the following table.



*a: Device Name List No. 1 Description
Name Component Connection Method
AVN Navigation ECU sub-assembly -

*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC. -
DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
NCON The device was previously present, but does not respond in diagnostic mode. Check power supply wire harness of the device.
NRES The device responds in diagnostic mode, but gives no DTC information. Check power supply wire harness of the device.

*e: Device Name List No. 2 Description
Name Component Connection Method
AUX No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E225773E03
0.677,0.677 0.333,0.677 true 0.885,1.094 0.885,1.865 true 2.146,1 2.146,1.885 true 2.479,1.729 2.479,1.885 true 0.844,0.104 1.146,0.104 1.146,0.104 1.396,0.594 true 2.177,0.104 1.865,0.104 1.865,0.104 1.719,0.417 true 2.208,0.021 2.406,0.188 0.198,0.167 10 *a 0.625,0.021 0.823,0.188 0.198,0.167 10 *b 0.135,0.583 0.333,0.75 0.198,0.167 10 *c 0.802,1.896 1,2.063 0.198,0.167 10 *d 2.031,1.896 2.229,2.063 0.198,0.167 10 *e 2.375,1.896 2.573,2.063 0.198,0.167 10 *f

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
*f: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and stored DTCs.




c.
E267334

Read the system check result.

i.

If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", this means that no DTCs are stored.

·

When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.







DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E267336

Clear DTCs

i.

Press the "Memory CLR" switch for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.





b.

Recheck

i.
E267337

Press the "Recheck" switch.


ii.
E270412

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

HINT:

When the DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

Turn the engine switch off.