Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2013.11–2014.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.

Check the radio automatic station search function.


b.

Check the radio automatic station search function by activating it.


Result:
Proceed to
Automatic station search function does not stop
Automatic station search function stops on a station



Automatic station search function does not stop

2.CHECK OPTIONAL COMPONENTS

Automatic station search function stops on a station

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

NOTICE:

Do not remove optional components without the permission of the customer.


Result:
Proceed to
Optional components are not installed
Optional components are installed




Optional components are not installed

3.CHECK NAVIGATION ECU SUB-ASSEMBLY

Optional components are installed

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.
E187251

Disconnect the antenna connector from the navigation ECU sub-assembly.


b.

Turn the engine switch on (ACC) with the navigation ECU sub-assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation ECU sub-assembly antenna jack and check that noise can be heard from the speakers.


Result:
Proceed to
Noise can be heard from the speakers
Noise cannot be heard from the speakers



Noise can be heard from the speakers

4.INSPECT NAVIGATION ECU SUB-ASSEMBLY

Noise cannot be heard from the speakers

4.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.

Disconnect the navigation ECU sub-assembly connector.


b.
E188455C15
0.667,0.5 1.156,0.76 0.49,0.26 1.542,1.094 1.271,1.563 1.271,1.563 1.146,1.563 true 0.094,0.052 0.271,0.219 0.177,0.167 10 *a 0.813,0.552 1.031,0.719 0.219,0.167 10 RA 0.74,1.479 1.135,1.646 0.396,0.167 10 ANT+
*a Component without harness connected
(Navigation ECU Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
RA-5 (ANT+) - Body ground Engine switch on (ACC)
Radio switch on and AM or FM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK ANTENNA CORD SUB-ASSEMBLY

b.

Check if radio broadcasts can be received normally.


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 2 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL


b.

Check if radio broadcasts can be received normally.


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (NO. 2 ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
7.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Replace the No. 3 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Roof Side)>REMOVAL


b.

Check if radio broadcasts can be received normally.


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (NO. 3 ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally

8.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
8.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION


Result:
Proceed to
The roof antenna pole sub-assembly is installed properly
The roof antenna pole sub-assembly is not installed properly



The roof antenna pole sub-assembly is installed properly

END (ROOF ANTENNA POLE SUB-ASSEMBLY IS DEFECTIVE)

The roof antenna pole sub-assembly is not installed properly

9.CHECK ANTENNA WITH HOLDER ASSEMBLY
9.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


b.

Check if radio broadcasts can be received normally.


Result:
Proceed to
Radio broadcasts can be received normally
Radio broadcasts cannot be received normally



Radio broadcasts can be received normally

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

Radio broadcasts cannot be received normally