Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2013.11–2014.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

WIRING DIAGRAM

E291565E01
2.302,0.552 4.135,0.75 1.833,0.198 10 false from Battery 2.094,1.323 3.927,1.521 1.833,0.198 10 false from ACC Relay 1.844,1.865 3.677,2.063 1.833,0.198 10 false from IG1 NO.1 Relay 3.906,0.74 4.792,0.958 0.885,0.219 10 false RADIO 3.958,1.521 4.844,1.74 0.885,0.219 10 false ACC 3.792,2.052 4.677,2.271 0.885,0.219 10 false ECU-IG NO.2 5.229,0.583 6.115,0.802 0.885,0.219 10 false G137 5.229,1.354 6.115,1.573 0.885,0.219 10 false G137 5.198,1.885 6.083,2.104 0.885,0.219 10 false G139 5.208,2.458 6.094,2.677 0.885,0.219 10 false G137 5.646,0.604 6.531,0.823 0.885,0.219 10 false +B1 5.656,1.344 6.542,1.563 0.885,0.219 10 false ACC1 5.646,1.885 6.531,2.104 0.885,0.219 10 false IG 5.656,2.448 6.542,2.667 0.885,0.219 10 false GND1 5.458,2.896 6.677,3.229 1.219,0.333 10 false Navigation Receiver Assembly 5.344,2.24 6.229,2.458 0.885,0.219 10 false 7 5.344,1.667 6.229,1.885 0.885,0.219 10 false 1 5.344,1.146 6.229,1.365 0.885,0.219 10 false 3 5.354,0.385 6.24,0.604 0.885,0.219 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
E256516C06
1.531,1.688 1.938,1.906 0.406,0.219 1.458,0.26 1.865,0.479 0.406,0.219 1.604,1.198 1.385,1.552 1.385,1.552 1.271,1.552 true 2.427,1.229 2.323,1.229 2.323,1.229 2.146,0.969 true 2.406,1.51 2.26,1.51 2.26,1.51 1.969,0.979 true 0.948,2.573 0.75,2.979 0.75,2.979 0.625,2.979 true 1.5,0.281 1.896,0.469 0.396,0.188 10 G137 1.583,1.719 1.99,1.896 0.406,0.177 10 G139 0.865,1.479 1.396,1.688 0.531,0.208 10 GND1 2.5,1.135 2.948,1.354 0.448,0.219 10 +B1 2.458,1.427 2.99,1.615 0.531,0.188 10 ACC1 0.448,2.896 0.865,3.125 0.417,0.229 10 IG 0.052,0.052 0.365,0.25 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Disconnect the navigation ECU sub-assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G137-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G137-4 (+B1) - G137-7 (GND1) Always 11 to 14 V
G137-3 (ACC1) - G137-7 (GND1) Engine switch on (ACC) 11 to 14 V
G139-1 (IG) - G137-7 (GND1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR