Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2WD) › 2014.10–2015.10
RM3090E _52 Drivetrain _008761 DRIVE SHAFT / PROPELLER SHAFT _0050235 FRONT DRIVE SHAFT ASSEMBLY(for 2WD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2WD)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 43448G 1.DISCONNECT FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

C127644C02
0.25,3.063 0.25,2.813 0.25,2.813 0.417,2.813 true 0.094,0.135 0.406,0.333 0.313,0.198 10 false *A 0.094,2.24 0.406,2.438 0.313,0.198 10 false *B 0.479,2.708 0.792,2.906 0.313,0.198 10 false *a
*A for One Touch Type
*B for Claw Engagement Type
*a Claw Engagement


a.

for One Touch Type:

Using a screwdriver, disconnect the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.


b.

for Claw Engagement Type:

Using needle-nose pliers, detach the claw engagement and disconnect the front No. 2 axle inboard joint boot clamp LH.


Hide 43448E 2.DISCONNECT FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43448F 3.DISCONNECT FRONT AXLE INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle inboard joint boot clamp LH.


Hide 43448C 4.DISCONNECT FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 5.DISCONNECT FRONT AXLE INBOARD JOINT BOOT

HINT:

Use the same procedure for the RH and LH sides.


a.

Disconnect the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 43040 6.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

C127646C04
2.167,0.396 2.167,0.25 2.167,0.25 1.083,0.25 true 1.833,0.802 1.833,0.25 true 0.875,0.167 1.167,0.354 0.292,0.188 10 *a
*a Matchmark


a.

Remove any old grease from the front drive inboard joint assembly LH.


b.

Put matchmarks on the front drive inboard joint assembly LH and front drive outboard joint shaft assembly LH.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the front drive inboard joint assembly LH from the front drive outboard joint shaft assembly LH.


d.
C127648

Using a snap ring expander, remove the snap ring.


e.
C127649C03
2.677,0.76 2.677,1.542 2.677,1.542 2.938,1.542 true 2.802,0.844 2.802,1.531 true 3,1.438 3.313,1.635 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly LH and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



f.

Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




g.

Remove the front No. 2 axle inboard joint boot clamp LH, front axle inboard joint boot and front axle inboard joint boot clamp LH.


Hide 43030 7.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43474G 8.DISCONNECT FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ Drive Shaft Damper)

a.
C311924C02
0.531,1.781 0.792,1.781 false 0.854,1.677 1.167,1.875 0.313,0.198 10 false *a
*a Claw Engagement


w/ 1 Clamp:

Using needle-nose pliers, detach the claw engagement and disconnect the front drive shaft damper clamp LH.


b.
C311855C02
1.875,0.75 2.031,0.844 2.031,0.844 2.219,0.844 true 2.281,0.75 2.594,0.948 0.313,0.198 10 false *a
*a Claw Engagement


w/ 2 Clamps:

Using needle-nose pliers, detach the claw engagement and disconnect the 2 front drive shaft damper clamp LH.

HINT:

Use the same procedure for each front drive shaft damper clamp LH.



Hide 43474F 9.DISCONNECT FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ Drive Shaft Damper)

HINT:

Use the same procedure described for the LH side.


Hide 43474E 10.REMOVE FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)

a.

w/ 1 Clamp:

Remove the front drive shaft damper LH and front drive shaft damper clamp LH from the front drive outboard joint shaft assembly LH.


b.

w/ 2 Clamps:

Remove the front drive shaft damper LH and 2 front drive shaft damper clamp LH from the front drive outboard joint shaft assembly LH.


Hide 43474D 11.REMOVE FRONT DRIVE SHAFT DAMPER RH (w/ Drive Shaft Damper)

HINT:

Use the same procedure described for the LH side.


Hide 43447F 12.DISCONNECT FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

C127653

a.

Using a screwdriver, disconnect the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.


Hide 43447D 13.DISCONNECT FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43447E 14.DISCONNECT FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front No. 2 axle outboard joint boot clamp LH.


Hide 43447C 15.DISCONNECT FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 16.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

HINT:

Use the same procedure for the RH and LH sides.


a.

Remove the front No. 2 axle outboard joint boot clamp, front axle outboard joint boot and front axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove any old grease from the front drive outboard joint shaft assembly.


Hide 41336E 17.REMOVE FRONT DRIVE SHAFT DUST COVER LH

C127659N02
0.792,1.771 0.969,1.771 0.969,1.771 1.208,1.385 true 0.438,1.698 0.865,1.844 0.427,0.146 10 SST

a.

Using SST and a press, remove the front drive shaft dust cover LH from the front drive inboard joint assembly LH.

SST
09950-00020  

NOTICE:

Do not drop the front drive inboard joint assembly LH.



Hide 41336D 18.REMOVE FRONT DRIVE SHAFT DUST COVER RH

a.
C311854N01
0.906,1.813 1.146,1.813 1.146,1.813 1.375,1.323 true 0.563,1.74 1.021,1.938 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft dust cover RH from the front drive inboard joint assembly RH.

SST
09950-00020  

NOTICE:

Do not drop the front drive inboard joint assembly RH.



Hide 43045 19.REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY (for RH Side)

a.

w/ Drive Shaft Bearing Case:

i.
C127662

Using a screwdriver, remove the bearing case snap ring from the drive shaft bearing case sub-assembly.


ii.
C127663

Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly RH.

NOTICE:

Do not drop the front drive inboard joint assembly RH.




Hide 43458 20.REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)

a.
C127664N02
1.219,1.5 1.021,1.323 1.021,1.323 0.625,1.323 true 0.281,1.24 0.573,1.385 0.292,0.146 10 SST

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly RH.

SST
09950-00020  

NOTICE:

Do not drop the front drive inboard joint assembly RH.



Hide 43410C 21.REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

C127665

a.

Using a snap ring expander, remove the snap ring.


b.
C127666N03
2.615,0.906 2.417,0.906 2.417,0.906 2.177,1.479 true 2.698,0.833 3.01,0.99 0.313,0.156 10 SST

Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly RH.

SST
09527-10011  

NOTICE:

Do not drop the front drive inboard joint assembly RH.