Home › Drivetrain › EB61F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008758 EB61F MANUAL TRANSMISSION / TRANSAXLE _0048577 DIFFERENTIAL CASE A

EB61F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 41311R 1.REMOVE FRONT DIFFERENTIAL CASE OIL SEAL

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.


·

Do not overtighten the vise.




b.
C318870N01
1.156,1.615 1.396,1.615 1.396,1.615 1.604,1.875 false 0.833,1.542 1.292,1.74 0.458,0.198 10 false SST

Using SST, remove the front differential case oil seal from the front differential case.

SST
09308-00010  


Hide 41221 2.REMOVE FRONT DIFFERENTIAL RING GEAR

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.


·

Do not overtighten the vise.




b.
C207064C01
1.99,0.49 1.208,0.167 false 1.208,0.167 0.5,0.167 false 1.927,0.667 1.208,0.167 false 0.26,0.083 0.51,0.271 0.25,0.188 10 *a
*a Matchmark


Put matchmarks on the front differential ring gear and front differential case.


c.
C199117

Remove the 12 bolts.


d.

Using a plastic-faced hammer, remove the front differential case from the front differential ring gear.


e.

Remove the front differential ring gear.


Hide 41311 3.INSPECT FRONT DIFFERENTIAL CASE

Hide 4.INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT

Hide 41342A 5.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C318873

Using a 5 mm pin punch and hammer, remove the front differential pinion shaft straight pin from the front differential case.


Hide 41342F 6.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C207066

Remove the front No. 1 differential pinion shaft from the front differential case.


Hide 7.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41039A 8.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Set SST as shown in the illustration and tighten it.

SST
09528-52010  (09953-05010, 09528-05010)

C318268C01
4.677,0.281 5.198,0.281 false 5.135,1.438 3.802,1.656 3.802,1.656 5.146,1.219 true 3.135,0.229 3.448,0.427 0.313,0.198 10 false *a 1.115,2.198 1.427,2.396 0.313,0.198 10 false *b 4.281,0.208 4.688,0.438 0.406,0.229 10 false SST 3.458,1.594 3.865,1.823 0.406,0.229 10 false SST
*a Turn *b Hold


NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, center differential side gear conical spring washer, front No. 1 differential side gear thrust washer and front differential case.


HINT:
·

Tighten SST until there is a clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C318269C01
2.448,2.031 2.135,0.823 2.135,0.823 2.375,0.823 true 1.292,1.385 1.604,1.583 0.313,0.198 10 false *a 2.479,0.75 2.969,0.927 0.49,0.177 10 false SST
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



c.
C318270C01
1.542,2.896 1.74,2.896 1.74,2.896 2.271,2.604 true 1.719,1.052 1.917,1.052 1.917,1.052 2.271,1.219 true 1.698,0.885 1.896,0.885 1.896,0.885 2.25,1.052 true 1.74,2.479 1.938,2.479 1.938,2.479 2.24,2.281 true 1.573,3.156 1.771,3.156 1.771,3.156 2.313,2.771 true 1.625,1.396 1.823,1.396 1.823,1.396 2.177,1.563 true 1.427,1.333 1.74,1.531 0.313,0.198 10 true *1 1.479,0.99 1.792,1.188 0.313,0.198 10 false *2 1.479,0.792 1.792,0.99 0.313,0.198 10 false *3 1.354,2.823 1.667,3.021 0.313,0.198 10 false *2 1.385,3.083 1.698,3.281 0.313,0.198 10 false *3 1.469,2.385 1.781,2.583 0.313,0.198 10 true *1
*1 Front Differential Side Gear
*2 Center Differential Side Gear Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front differential case, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 center differential side gear conical spring washers from the front differential case.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and center differential side gear conical spring washer.