Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008756 EA64F MANUAL TRANSMISSION / TRANSAXLE _0048565 DIFFERENTIAL CASE G

EA64F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  INSPECTION  


PROCEDURE

Hide 41301L 1.INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C318257N01
0.792,1.698 1.094,1.698 1.094,1.698 1.573,2.208 true 0.479,1.615 0.938,1.813 0.458,0.198 10 false SST

Using SST, rotate the front differential side gear as shown in the illustration.

SST
09528-52010  (09528-05030)

Standard:

The front differential side gear does not lock when rotated in either direction.


·

If the front differential side gear locks, perform all remaining inspection procedures.

·

Replace any parts that do not meet the specifications.

·

If the front differential side gear locks after performing the inspection procedures, replace the front No. 1 differential case sub-assembly.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

a.

Set SST as shown in the illustration and tighten it.

SST
09528-52010  (09528-05010, 09953-05010)

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C318258C01
4.646,0.333 5.271,0.333 false 5.125,1.323 4.583,1.219 4.583,1.219 5.146,1.115 true 3.094,0.458 3.406,0.656 0.313,0.198 10 false *a 0.958,2.438 1.271,2.635 0.313,0.198 10 false *b 4.281,0.25 4.594,0.448 0.313,0.198 10 false SST 4.24,1.146 4.552,1.344 0.313,0.198 10 false SST
*a Turn *b Hold



b.
C318259C01
2.031,0.354 2.479,0.354 false 2.552,0.292 2.865,0.49 0.313,0.198 10 false *1
*1 Front No. 1 Differential Pinion Shaft


Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.


c.

Using a dial indicator, measure the front differential pinion backlash.

Standard Backlash:

0.15 mm (0.00591 in.) or less


If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.

Front No. 1 Differential Side Gear Thrust Washer Thickness:
Specified Condition
1.25 mm (0.0492 in.)
1.30 mm (0.0512 in.)
1.35 mm (0.0531 in.)
1.40 mm (0.0551 in.)
1.45 mm (0.0571 in.)
1.50 mm (0.0591 in.)
1.55 mm (0.0610 in.)
1.60 mm (0.0630 in.)
1.65 mm (0.0650 in.)
1.70 mm (0.0669 in.)
1.75 mm (0.0689 in.)
1.80 mm (0.0709 in.)
1.85 mm (0.0728 in.)
1.90 mm (0.0748 in.)
1.95 mm (0.0768 in.)


HINT:

Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.



Hide 41351F 3.INSPECT FRONT DIFFERENTIAL PINION THRUST WASHER

a.
C288044

Using a micrometer, measure the thickness of the front differential pinion thrust washer.

Minimum Thickness:

0.54 mm (0.0213 in.)


If the thickness is less than the minimum, replace the front differential pinion thrust washer.


Hide 41342F 4.INSPECT FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C291384C02
2.563,1.115 2.875,1.271 0.313,0.156 10 false *a
*a Outer Diameter


Using a micrometer, measure the outer diameter of the front No. 1 differential pinion shaft.

Minimum Outer Diameter:

20.499 mm (0.807 in.)


If the outer diameter is less than the minimum, replace the front No. 1 differential pinion shaft.