Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CYLINDER BLOCK › 2014.10–2015.04
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046952 CYLINDER BLOCK A

3ZR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 12211 1.REMOVE NO. 1 VENTILATION CASE

HINT:

There are 2 installation methods for the No. 1 ventilation case. Depending on the installation method, the number of bolts, nuts and stud bolts used will vary.


a.
A205919

for Type A:

Remove the 6 bolts and 2 nuts.


b.
A234594

for Type B:

Remove the 8 bolts.


c.
A234595C02
3.073,2.521 2.979,2.521 2.979,2.521 2.906,2.396 false 1.75,3.188 1.615,3.188 1.615,3.188 0.979,3 true 1.771,3.083 2.083,3.281 0.313,0.198 10 *1 3.104,2.438 3.333,2.625 0.229,0.188 10 *1
*1 Protective Tape


Remove the No. 1 ventilation case by prying between the No. 1 ventilation case and cylinder block with a screwdriver as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and No. 1 ventilation case.


HINT:

Tape the screwdriver tip before use.



Hide 2.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A208475

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.160 to 0.342 mm (0.00630 to 0.0135 in.)


Maximum thrust clearance:

0.342 mm (0.0135 in.)


If the thrust clearance is more than the maximum, replace the connecting rod assemblies as necessary. If necessary, replace the crankshaft.


Hide 3.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A205921C02
1.344,0.208 1.219,0.208 1.219,0.208 0.771,0.76 true 1.375,0.146 1.625,0.333 0.25,0.188 10 *1
*1 Matchmark


Check that the matchmarks on the connecting rod and cap are aligned to ensure correct reassembly.

HINT:

The matchmarks on the connecting rods and caps are provided to ensure correct reassembly.



b.
A205922N02
0.521,0.833 0.635,0.833 0.635,0.833 1.281,0.615 true 0.177,0.75 0.552,0.927 0.375,0.177 10 SST

Using SST, uniformly loosen and remove the 2 bolts.

SST
09205-16011  


c.
A205923

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower bearing inserted in the connecting rod cap.



d.

Clean the crank pin and bearing.


e.

Check the crank pin and bearing for pitting and scratches.

If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.


f.
A150964C08
1.167,0.25 1.281,0.25 1.281,0.25 1.708,0.854 true 0.979,0.167 1.188,0.344 0.208,0.177 10 *1
*1 Plastigage


Lay a strip of Plastigage on the crank pin.


g.
A208476C03
1.333,0.146 1.5,0.146 1.5,0.146 1.5,0.677 true 1.115,0.052 1.313,0.24 0.198,0.188 10 *1
*1 Front Mark


Check that the front mark of the connecting rod cap is facing forward and install the connecting rod cap.


h.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


i.

Install the connecting rod cap bolts.

NOTICE:

The connecting rod cap bolts should be tightened in 2 progressive steps.



j.

Step 1:

i.
A208477E01
0.534,0.117 0.838,0.268 0.304,0.151 10 SST 0.918,0.215 1.044,0.215 1.044,0.215 1.319,0.518 false

Using SST, install and alternately tighten the bolts of the connecting rod cap in several steps.

SST
09205-16011  

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not turn the crankshaft.




k.

Step 2:

i.

Mark the front side of each connecting rod cap bolts with paint.


ii.

Tighten the cap bolts 90°.

NOTICE:

Do not turn the crankshaft.



iii.

Check that the paint marks are now at a 90° angle to the front.



l.

Remove the 2 bolts and connecting rod cap.

HINT:

Keep the lower bearing inserted in the connecting rod cap.



m.
A150976C09
0.896,0.354 1.052,0.354 1.052,0.354 1.427,1.125 true 1.458,4.063 1.177,3.135 1.177,3.135 1.51,3.135 true 1.51,3.417 1.177,3.135 true 0.688,0.26 0.896,0.438 0.208,0.177 10 *1 0.927,3.052 1.125,3.229 0.198,0.177 10 *2
*1 Plastigage
*2 1, 2 or 3 Mark


Measure the Plastigage at its widest point.

Standard oil clearance:

0.030 to 0.062 mm (0.00118 to 0.00244 in.)


Maximum oil clearance:

0.070 mm (0.00276 in.)


If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, inspect the crankshaft.

NOTICE:

Remove the Plastigage completely after the measurement.


HINT:

If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. Each standard bearing thickness is indicated by a 1, 2, or 3 mark on its surface.


Standard Connecting Rod Large End Bore Diameter:
Item Specified Condition
Mark 1 50.000 to 50.008 mm (1.9685 to 1.9688 in.)
Mark 2 50.008 to 50.016 mm (1.9688 to 1.9691 in.)
Mark 3 50.016 to 50.024 mm (1.9691 to 1.9694 in.)


Standard Connecting Rod Bearing Thickness:
Item Specified Condition
Mark 1 1.489 to 1.493 mm (0.0586 to 0.0588 in.)
Mark 2 1.493 to 1.497 mm (0.0588 to 0.0589 in.)
Mark 3 1.497 to 1.501 mm (0.0589 to 0.0591 in.)


Standard crankshaft pin diameter:

46.992 to 47.000 mm (1.8501 to 1.8504 in.)



n.

Perform the inspection above for each cylinder.


Hide 4.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A157789

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Push the piston, connecting rod and upper bearing through the top of the cylinder block.

HINT:
·

Keep the bearing, connecting rod and cap together.

·

Arrange the piston and connecting rod assemblies in the correct order.

·

Be sure to arrange the removed piston and connecting rod assemblies in such a way that they can be reinstalled exactly as before.




Hide 13041 5.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 6.REMOVE PISTON RING SET

a.
A150977C02
0.688,1.552 0.688,1.438 0.688,1.438 1.167,1.177 false 0.635,1.573 0.833,1.75 0.198,0.177 10 *1
*1 Piston Ring Expander


Using a piston ring expander, remove the 2 compression rings.


b.

for Type W and type X:

Remove the oil ring and oil ring expander by hand.

HINT:

Arrange the removed parts in the correct order.



c.

for Type Y and type Z:

Remove the oil ring expander and 2 oil ring side rails by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 7.REMOVE PISTON

a.
A150978

Using a screwdriver, pry out the 2 snap rings.


b.

Gradually heat each piston to approximately 80 to 90°C (176 to 194°F).


c.
A106279

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and pin are a matched set.

·

Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.




Hide 8.INSPECT CRANKSHAFT THRUST CLEARANCE

a.

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.04 to 0.14 mm (0.00157 to 0.00551 in.)


Maximum thrust clearance:

0.18 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the upper crankshaft thrust washers as a set. If necessary, replace the crankshaft.

HINT:

The thrust washer thickness is 2.43 to 2.48 mm (0.0957 to 0.0976 in.).



Hide 13411 9.REMOVE CRANKSHAFT

a.
A297850N01
2.948,0.458 3.104,0.656 0.156,0.198 10 1 2.969,1.677 3.125,1.875 0.156,0.198 10 2 0.448,0.49 0.604,0.688 0.156,0.198 10 3 0.438,1.667 0.594,1.865 0.156,0.198 10 4 2.406,0.406 2.563,0.604 0.156,0.198 10 5 2.417,1.729 2.573,1.927 0.156,0.198 10 6 1.042,0.427 1.198,0.625 0.156,0.198 10 7 1.021,1.729 1.177,1.927 0.156,0.198 10 8 1.719,1.781 1.875,1.979 0.156,0.198 10 9 1.667,0.385 1.896,0.563 0.229,0.177 10 10

Uniformly loosen and remove the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.


b.
A205925

Use the removed crankshaft bearing cap bolts to remove the 5 crankshaft bearing caps and 5 lower bearings.

NOTICE:

Insert the bolts into the caps in turn. Ease the cap out by gently pulling up and applying force toward the front and back sides of the cylinder block as shown in the illustration. Take care not to damage the contact surfaces of the cap and cylinder block.


HINT:
·

Keep each lower bearing and crankshaft bearing cap together as a set.

·

Arrange the crankshaft bearing caps in the correct order.




c.

Lift out the crankshaft.


d.

Check each crankshaft journal and bearing for pitting and scratches.

If the journal or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.


Hide 11791 10.REMOVE UPPER CRANKSHAFT THRUST WASHER

a.
A150982

Remove the 2 upper crankshaft thrust washers from the cylinder block.


Hide 11711 11.REMOVE CRANKSHAFT BEARING

a.
A150983

Remove the 5 upper crankshaft bearings from the cylinder block.

HINT:

Arrange the bearings in the correct order.



b.
A150984

Remove the 5 lower crankshaft bearings from the 5 crankshaft bearing caps.

HINT:

Arrange the bearings in the correct order.



Hide 15708 12.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A205926

Using a 5 mm socket hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzles.


Hide 11432A 13.REMOVE NO. 1 TAPER SCREW PLUG

a.
A300839

Remove the No. 1 taper screw plug.


Hide 14.CLEAN CYLINDER BLOCK

NOTICE:

If the cylinder is washed at high temperatures, the cylinder liner will stick out beyond the cylinder block. Always wash the cylinder block at a temperature of 45°C (113°F) or less.


Hide 15.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.