Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049182 DIFFERENTIAL CASE G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  INSPECTION  


PROCEDURE

Hide 41311 1.INSPECT FRONT DIFFERENTIAL CASE

a.
C288233N03
1.792,1.302 2.01,1.063 2.01,1.063 2.396,1.063 true 2.458,0.979 2.917,1.177 0.458,0.198 10 false SST

Using SST, rotate the front differential side gear as shown in the illustration.

SST
09528-52010  (09528-05030)

Standard:

The front differential side gear does not lock when rotated in either direction.


·

If the front differential side gear locks, perform all inspections.

·

If the front differential side gear still locks even after replacing the malfunctioning parts, replace the front differential case.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

a.

Install SST as shown in the illustration and tighten it.

C288646C02
4.594,0.417 5.042,0.417 false 4.979,1.771 4.417,1.646 4.417,1.646 4.979,1.51 true 2.854,0.563 3.167,0.719 0.313,0.156 10 false *a 0.5,2.188 0.813,2.344 0.313,0.156 10 false *b 4.281,0.344 4.74,0.542 0.458,0.198 10 false SST 4.115,1.563 4.573,1.76 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Secure the front differential case with front differential ring gear in a vise between aluminum plates

NOTICE:

Do not overtighten the vise.



c.
C301362C02
1.844,0.313 2.302,0.313 true 0.302,2.219 0.646,1.375 0.646,1.375 1.083,2.646 true 1.615,0.24 1.927,0.438 0.313,0.198 10 false *1 0.51,1.198 0.969,1.396 0.458,0.198 10 false SST
*1 Front No. 1 Differential Pinion Shaft


Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.


d.

Using a dial indicator, measure the front differential pinion backlash.

Standard Backlash:

0.20 mm (0.00787 in.) or less


If the backlash is not as specified, replace the 2 front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.

Front No. 1 Differential Side Gear Thrust Washer Thickness:
Part No. Thickness (mm (in.))
41361-73050 0.90 (0.0354)
41361-73010 1.00 (0.0394)
41361-73020 1.10 (0.0433)
41361-73030 1.20 (0.0472)

HINT:

Select 2 front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.



Hide 41351F 3.INSPECT FRONT DIFFERENTIAL PINION THRUST WASHER

a.
C288044

Using a micrometer, measure the thickness of the front differential pinion thrust washer.

Minimum Thickness:

0.90 mm (0.0954 in.)


HINT:

Measure the most worn portion of the front differential pinion thrust washer.


If the thickness is less than the minimum, replace the front differential pinion thrust washer.


Hide 41342F 4.INSPECT FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C291384

Using a micrometer, measure the outer diameter of the front No. 1 differential pinion shaft.

Minimum Outer Diameter:

17.975 mm (0.708 in.)


HINT:

Measure the most worn portion of the front No. 1 differential pinion shaft.


If the outer diameter is less than the minimum, replace the front No. 1 differential pinion shaft.