Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2014.10–2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Navigation Voice Circuit  


DESCRIPTION

This circuit is used when the voice guidance in the navigation system is on or an incoming cellular phone voice in the "Bluetooth" hands-free system is heard.

Using this circuit, the radio and display receiver assembly sends the signals to the stereo component amplifier assembly.

WIRING DIAGRAM

E307296E01
1.167,0.646 1.625,0.844 0.458,0.198 10 false SLD1 1.281,1.438 1.74,1.635 0.458,0.198 10 false II1+ 1.292,2.219 1.75,2.417 0.458,0.198 10 false II1- 0.313,2.656 0.771,2.854 0.458,0.198 10 false M32 0.313,2.813 2.052,3.156 1.74,0.344 10 false Stereo Component Amplifier Assembly 2.198,2.563 2.385,2.719 0.188,0.156 10 false * 3.479,2.552 3.667,2.708 0.188,0.156 10 false * 0.146,3.438 3.104,3.625 2.958,0.188 10 false *: Shielded 5.406,1.333 5.594,1.49 0.188,0.156 10 false 2 5.406,2.125 5.594,2.281 0.188,0.156 10 false 6 5.604,1.448 6.063,1.646 0.458,0.198 10 false RL+ 5.635,2.281 6.094,2.479 0.458,0.198 10 false RL- 5.302,2.656 5.76,2.854 0.458,0.198 10 false G142 5.333,2.813 7.021,3.135 1.688,0.323 10 false Radio and Display Receiver Assembly 1.625,0.542 2.083,0.74 0.458,0.198 10 false 18 1.604,1.344 2.063,1.542 0.458,0.198 10 false 15 1.615,2.135 2.073,2.333 0.458,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G142 radio and display receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-15 (II1+) - G142-2 (RL+) Always Below 1 Ω
M32-14 (II1-) - G142-6 (RL-) Always Below 1 Ω
M32-15 (II1+) - Body ground Always 10 kΩ or higher
M32-14 (II1-) - Body ground Always 10 kΩ or higher
M32-18 (SLD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR