Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2014.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066373 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The front passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH.

DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit.

Troubleshoot DTC B1771 first when DTCs B1771 and B1795 are output simultaneously.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1771 Passenger Side Buckle Switch Circuit Malfunction
One of the following conditions is met:
·

Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the front passenger side buckle switch circuit for 2 seconds.

·

Front passenger side buckle switch malfunction.

·

Occupant detection ECU malfunction.


·

Front seat wire RH

·

Front seat inner belt assembly RH

·

Occupant detection ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1771 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C253566E30
0.333,4.083 2.531,4.438 2.198,0.354 10 false Front Seat Inner Belt Assembly RH 5.667,3.896 5.969,4.073 0.302,0.177 10 false d16 5.635,4.073 6.865,4.406 1.229,0.333 10 false Occupant Detection ECU 5.646,1.26 5.813,1.427 0.167,0.167 10 false 8 5.646,2.823 5.813,2.99 0.167,0.167 10 false 5 2.448,2.802 2.604,3 0.156,0.198 10 false 2 2.458,1.24 2.615,1.438 0.156,0.198 10 false 1 0.323,3.896 0.729,4.115 0.406,0.219 10 false d25

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause a problem, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

DTC B1771 is output

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

3.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.
C281859C01
0.74,1.625 1.052,1.823 0.313,0.198 10 false *1 2.583,1.51 2.896,1.708 0.313,0.198 10 false *2 1.615,1.406 1.927,1.604 0.313,0.198 10 false *3
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH


Disconnect the connectors from the occupant detection ECU and the front seat inner belt assembly RH.


b.

Check that the connectors (on the occupant detection ECU side and the front seat inner belt assembly RH side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

4.CHECK DTC

Connectors are deformed or damaged

REPLACE FRONT SEAT WIRE RH

4.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

DTC B1771 is output

5.CHECK FRONT SEAT WIRE RH
5.CHECK FRONT SEAT WIRE RH
C314592C05
5.917,0.25 6.25,0.417 0.333,0.167 3.75,0.25 4.083,0.417 0.333,0.167 5.74,1.521 5.823,1.438 false 0.677,1.365 0.99,1.521 0.313,0.156 10 false *1 2.156,1.313 2.469,1.469 0.313,0.156 10 false *2 1.354,0.781 1.667,0.938 0.313,0.156 10 false *3 4.521,0.823 4.833,0.979 0.313,0.156 10 false *4 6.521,0.906 6.833,1.063 0.313,0.156 10 false *5 5.563,1.542 5.875,1.698 0.313,0.156 10 false *6 3.365,0.427 3.677,0.583 0.313,0.156 10 false *a 5.594,0.469 5.906,0.625 0.313,0.156 10 false *b 3.802,0.26 4.302,0.5 0.5,0.24 10 false d16 6,0.25 6.5,0.49 0.5,0.24 10 false d25 2.01,0.969 2.26,1.125 0.25,0.156 10 false A 1.667,1.198 1.917,1.354 0.25,0.156 10 false B 1.167,1.177 1.417,1.333 0.25,0.156 10 false C 0.802,0.969 1.052,1.125 0.25,0.156 10 false D
*1 Front Seat Inner Belt Assembly RH *2 Occupant Detection ECU
*3 Front Seat Wire RH *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d16-8 - Body ground Ignition switch ON Below 1 V
d16-5 - Body ground



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


d.

Using service wires, connect terminals 1 and 2 of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-8 - d16-5 Always Below 1 Ω



f.

Disconnect the service wires from connector C.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-8 - d16-5 Always 1 MΩ or higher
d16-8 - Body ground
d16-5 - Body ground



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPLACE FRONT SEAT WIRE RH

6.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.

Replace the front seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1771 is not output
DTC B1771 is output


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.




DTC B1771 is not output

END (FRONT SEAT INNER BELT ASSEMBLY RH WAS DEFECTIVE)

DTC B1771 is output

7.REPLACE OCCUPANT DETECTION ECU
7.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Result:
Proceed to
NEXT



NEXT

8.PERFORM ZERO POINT CALIBRATION
8.PERFORM ZERO POINT CALIBRATION

Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

9.PERFORM SENSITIVITY CHECK
9.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)