The front occupant classification sensor LH circuit consists of the occupant detection ECU and front occupant classification sensor LH.
DTC B1780 is stored when a malfunction is detected in the front occupant classification sensor LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1780 | Front Occupant Classification Sensor LH Circuit Malfunction | One of the following conditions is met:
·
Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the front occupant classification sensor LH circuit for 2 seconds. ·
Front occupant classification sensor LH malfunction. ·
Occupant detection ECU malfunction. |
·
Separate type front seat cushion spring assembly (front occupant classification sensor LH) ·
Front seat wire RH ·
Occupant detection ECU |
When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1780 of the occupant classification system.
Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.
In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1780 is not output |
| DTC B1780 is output |
DTCs other than DTC B1780 may be output at this time, but they are not related to this check.
DTC B1780 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1780 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant detection ECU and front occupant classification sensor LH.
| Proceed to |
|---|
| Connectors are properly connected |
| Connectors are not properly connected |
Connectors are properly connected
Connectors are not properly connected
| *1 | Front Occupant Classification Sensor LH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
Disconnect the connectors from the occupant detection ECU and front occupant classification sensor LH.
Check that the connectors (on the occupant detection ECU side and front occupant classification sensor LH side) are not damaged.
Click here
| Proceed to |
|---|
| Connectors are not deformed or damaged |
| Connectors are deformed or damaged |
Connectors are not deformed or damaged
Connectors are deformed or damaged
| *1 | Front Seat Wire RH |
| *2 | Front Occupant Classification Sensor LH |
| *3 | Occupant Detection ECU |
| *4 | Service Wire |
| *5 | Connector C |
| *6 | Connector B |
| *a | Front view of wire harness connector
(to Front Occupant Classification Sensor LH) |
| *b | Front view of wire harness connector
(to Occupant Detection ECU) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| d15-1 - Body ground | Ignition switch to ON | Below 1 V |
| d15-3 - Body ground | ||
| d15-5 - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using service wires, connect terminals 1 and 3, and terminals 2 and 3 of connector C.
Do not forcibly insert the service wires into the terminals of the connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d15-1 - d15-5 | Always | Below 1 Ω |
| d15-3 - d15-5 |
Disconnect the service wires from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d15-1 - d15-5 | Always | 1 MΩ or higher |
| d15-3 - d15-5 | ||
| d15-1 - d15-3 | ||
| d15-1 - Body ground | ||
| d15-3 - Body ground | ||
| d15-5 - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the occupant detection ECU and front occupant classification sensor LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1780 is not output |
| DTC B1780 is output |
DTCs other than DTC B1780 may be output at this time, but they are not related to this check.
DTC B1780 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1780 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
Perform the inspection using parts from a normal vehicle when possible.
"Zero Point Calibration is complete." is displayed
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
| "Zero Point Calibration is complete." is not displayed |
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1780 is not output |
| DTC B1780 is output |
DTCs other than DTC B1780 may be output at this time, but they are not related to this check.
DTC B1780 is not output
DTC B1780 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the separate type front seat cushion spring assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY
Perform the inspection using parts from a normal vehicle when possible.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
"Zero Point Calibration is complete." is displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| NEXT |
NEXT