Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2014.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066373 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1785  Front Occupant Classification Sensor LH Collision Detection  


DESCRIPTION

DTC B1785 is stored when the occupant detection ECU receives a collision detection signal, which is sent by the front occupant classification sensor LH when an accident occurs.

DTC B1785 is also stored when the separate type front seat cushion spring assembly is subjected to a strong impact, even if an actual accident has not occurred.

However, when the occupant detection ECU outputs a collision detection signal, even if the vehicle has not been in a collision, DTC B1785 can be cleared by conducting the zero point calibration and sensitivity check.

Therefore, if DTC B1785 is output, first perform the zero point calibration and sensitivity check.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1785 Front Occupant Classification Sensor LH Collision Detection
Either condition is met:
·

Occupant detection ECU receives a collision detection signal, which is sent by the front occupant classification sensor LH when an accident occurs.

·

Separate type front seat cushion spring assembly is subjected to a strong impact, regardless of whether or not an actual accident has occurred.


·

Separate type front seat cushion spring assembly (front occupant classification sensor LH)

·

Occupant detection ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1785 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C239232E45
0.552,3.063 3.25,3.396 2.698,0.333 10 false Front Occupant Classification Sensor LH 5.344,3.073 7.073,3.448 1.729,0.375 10 false Occupant Detection ECU 1.844,0.521 2.177,0.969 0.333,0.448 10 false 1 1.844,1.396 2.125,1.771 0.281,0.375 10 false 2 1.844,2.271 2.167,2.646 0.323,0.375 10 false 3 5.229,0.531 5.448,0.74 0.219,0.208 10 false 1 5.229,1.406 5.448,1.688 0.219,0.281 10 false 3 5.229,2.26 5.583,2.656 0.354,0.396 10 false 5 5.344,2.906 5.708,3.115 0.365,0.208 10 false d15 0.563,2.906 1.063,3.24 0.5,0.333 10 false d26

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1785 is not output
DTC B1785 is output


HINT:

DTCs other than DTC B1785 may be output at this time, but they are not related to this check.




DTC B1785 is not output

DTC B1785 is output

2.PERFORM ZERO POINT CALIBRATION
2.PERFORM ZERO POINT CALIBRATION

Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

3.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT OCCUPANT CLASSIFICATION SENSOR LH)
3.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT OCCUPANT CLASSIFICATION SENSOR LH)
4.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1785 is not output
DTC B1785 is output


HINT:

DTCs other than DTC B1785 may be output at this time, but they are not related to this check.




DTC B1785 is not output

END

DTC B1785 is output

5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT OCCUPANT CLASSIFICATION SENSOR LH)
5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT OCCUPANT CLASSIFICATION SENSOR LH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


HINT:

Perform the inspection using parts from a normal vehicle when possible.


Result:
Proceed to
NEXT



NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

7.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

9.REPLACE OCCUPANT DETECTION ECU
7.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

8.CHECK DTC

NG

9.REPLACE OCCUPANT DETECTION ECU
8.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1785 is not output
DTC B1785 is output


HINT:

DTCs other than DTC B1785 may be output at this time, but they are not related to this check.




DTC B1785 is not output

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY [FRONT OCCUPANT CLASSIFICATION SENSOR LH] WAS DEFECTIVE)

DTC B1785 is output

9.REPLACE OCCUPANT DETECTION ECU
9.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



Result:
Proceed to
NEXT



NEXT

10.PERFORM ZERO POINT CALIBRATION
10.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

11.PERFORM SENSITIVITY CHECK
11.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)