Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2014.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066373 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1793  Occupant Classification Sensor Power Supply Circuit Malfunction  


DESCRIPTION

The occupant classification sensor power supply circuit consists of the occupant detection ECU, front and rear occupant classification sensor LH.

DTC B1793 is stored when a malfunction is detected in the occupant classification sensor power supply circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1793 Occupant Classification Sensor Power Supply Circuit Malfunction
One of the following conditions is met:
·

Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the occupant classification sensor power supply circuit for 2 seconds.

·

Open circuit in the occupant classification sensor wire harness.

·

Occupant detection ECU malfunction.


·

Separate type front seat cushion spring assembly (Front and rear occupant classification sensor LH)

·

Front seat wire RH

·

Occupant detection ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1793 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C239233E13
0.573,3.052 3.719,3.542 3.146,0.49 10 false Rear Occupant Classification Sensor LH 0.573,1.271 3.729,1.719 3.156,0.448 10 false Front Occupant Classification Sensor LH 0.583,2.896 1.094,3.208 0.51,0.313 10 false d24 5.333,2.896 5.74,3.156 0.406,0.26 10 false d15 0.563,1.115 0.99,1.333 0.427,0.219 10 false d26 5.333,3.063 7,3.354 1.667,0.292 10 false Occupant Detection ECU 1.844,2.281 2.188,2.677 0.344,0.396 10 false 1 1.844,0.49 2.25,0.896 0.406,0.406 10 false 1 5.219,2.281 5.563,2.604 0.344,0.323 10 false 2 5.219,0.49 5.531,0.844 0.313,0.354 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1793 is not output
DTC B1793 is output


HINT:

DTCs other than DTC B1793 may be output at this time, but they are not related to this check.




DTC B1793 is not output

DTC B1793 is output

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU, front and rear occupant classification sensor LH.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

3.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.
C256408C02
0.708,0.99 1.021,1.146 0.313,0.156 10 false *1 0.75,1.833 1.063,1.99 0.313,0.156 10 false *2 2.427,1.51 2.74,1.667 0.313,0.156 10 false *3 1.552,1.583 1.865,1.74 0.313,0.156 10 false *4
*1 Front Occupant Classification Sensor LH
*2 Rear Occupant Classification Sensor LH
*3 Occupant Detection ECU
*4 Front Seat Wire RH


Disconnect the connectors from the occupant detection ECU, front and rear occupant classification sensor LH.


b.

Check that the connectors (on the occupant detection ECU side, front and rear occupant classification sensor LH side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

4.CHECK FRONT SEAT WIRE RH

Connectors are deformed or damaged

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C256409C07
3.958,0.688 4.375,0.917 0.417,0.229 3.875,2.615 4.292,2.844 0.417,0.229 0.219,2.677 0.635,2.906 0.417,0.229 1.396,0.813 1.708,0.969 0.313,0.156 10 false *1 0.771,0.844 1.083,1 0.313,0.156 10 false *2 0.75,1.646 1.063,1.802 0.313,0.156 10 false *3 2.313,1.365 2.625,1.521 0.313,0.156 10 false *4 6.281,0.823 6.594,0.979 0.313,0.156 10 false *5 2.344,2.76 2.656,2.917 0.313,0.156 10 false *6 6.156,2.667 6.469,2.823 0.313,0.156 10 false *7 2.229,0.833 2.427,1.042 0.198,0.208 10 false A 5.406,0.156 5.719,0.313 0.313,0.156 10 false *a 1.531,2.115 1.844,2.271 0.313,0.156 10 false *b 5.365,2.031 5.677,2.188 0.313,0.156 10 false *c 1.917,1.042 2.073,1.198 0.156,0.156 10 false B 1.188,0.688 1.344,0.844 0.156,0.156 10 false C 1.198,1.448 1.354,1.604 0.156,0.156 10 false E 0.865,0.469 1.021,0.625 0.156,0.156 10 false D 4.063,0.729 4.375,0.885 0.313,0.156 10 false d15 0.896,1.25 1.052,1.406 0.156,0.156 10 false F 4.01,2.646 4.323,2.802 0.313,0.156 10 false d24 0.333,2.698 0.646,2.854 0.313,0.156 10 false d26 1.385,2.76 1.698,2.917 0.313,0.156 10 false 1 1.552,2.76 1.865,2.917 0.313,0.156 10 false 2 1.708,2.76 2.021,2.917 0.313,0.156 10 false 3 5.24,2.708 5.552,2.865 0.313,0.156 10 false 1 5.406,2.708 5.719,2.865 0.313,0.156 10 false 2 5.563,2.708 5.875,2.865 0.313,0.156 10 false 3
*1 Front Seat Wire RH *2 Front Occupant Classification Sensor LH
*3 Rear Occupant Classification Sensor LH *4 Occupant Detection ECU
*5 Connector B *6 Connector C
*7 Connector E - -
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Occupant Classification Sensor LH)
*c Front view of wire harness connector
(to Rear Occupant Classification Sensor LH)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d15-1 - Body ground Ignition switch ON Below 1 V
d15-2 - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d15-1 - d26-1 Always Below 1 Ω
d15-2 - d24-1
d15-1 - d15-2 1 MΩ or higher
d15-1 - Body ground
d15-2 - Body ground



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK DTC
a.

Connect the connectors to occupant detection ECU, front and rear occupant classification sensor LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1793 is not output
DTC B1793 is output


HINT:

DTCs other than DTC B1793 may be output at this time, but they are not related to this check.




DTC B1793 is not output

DTC B1793 is output

6.REPLACE OCCUPANT DETECTION ECU
6.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



Result:
Proceed to
NEXT



NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

8.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (OCCUPANT CLASSIFICATION SENSOR LH)
8.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

9.CHECK DTC

NG

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (OCCUPANT CLASSIFICATION SENSOR LH)
9.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1793 is not output
DTC B1793 is output


HINT:

DTCs other than DTC B1793 may be output at this time, but they are not related to this check.




DTC B1793 is not output

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

DTC B1793 is output

10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (OCCUPANT CLASSIFICATION SENSOR LH)
10.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (OCCUPANT CLASSIFICATION SENSOR LH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


HINT:

Perform the inspection using parts from a normal vehicle when possible.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

12.PERFORM SENSITIVITY CHECK
12.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY [OCCUPANT CLASSIFICATION SENSOR LH] WAS DEFECTIVE)