Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2014.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066373 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1794  Open in Occupant Classification ECU Battery Positive Line  


DESCRIPTION

DTC B1794 is stored when a malfunction is detected in the occupant detection ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1794 Open in Occupant Classification ECU Battery Positive Line
One of the following conditions is met:
·

Occupant detection ECU circuit malfunction.

·

Occupant detection ECU malfunction.


·

Harness or connector

·

Occupant detection ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1794 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C256410E11
4.906,3.125 6.49,3.302 1.583,0.177 10 false Occupant Detection ECU 4.906,2.958 5.198,3.125 0.292,0.167 10 false d16 0.729,1.49 1.76,1.698 1.031,0.208 10 false from IG2 Relay 3.229,1.01 4.396,1.271 1.167,0.26 10 false ECU-B NO.2 0.938,0.813 1.76,1.031 0.823,0.219 10 false from Battery 3.49,1.698 4.167,1.885 0.677,0.188 10 false A/B 5.031,2 5.188,2.198 0.156,0.198 10 false 3 5.042,1.375 5.198,1.573 0.156,0.198 10 false 6 5.042,0.708 5.198,0.906 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If troubleshooting (wire harness inspection) is difficult to perform, remove the frontseat RH installation bolts to see the undersurface of the seat cushion.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1794 is not output
DTC B1794 is output


HINT:

DTCs other than DTC B1794 may be output at this time, but they are not related to this check.




DTC B1794 is not output

DTC B1794 is output

2.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the occupant detection ECU.


Result:
Proceed to
Connector is properly connected
Connector is not properly connected



Connector is properly connected

3.CHECK CONNECTOR

Connector is not properly connected

CONNECT CONNECTOR

3.CHECK CONNECTOR
a.

Disconnect the connector from the occupant detection ECU.


b.

Check that the connector (on the occupant detection ECU side) is not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

4.CHECK HARNESS AND CONNECTOR (OCCUPANT DETECTION ECU - BATTERY AND BODY GROUND)

Connectors are deformed or damaged

REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (OCCUPANT DETECTION ECU - BATTERY AND BODY GROUND)
a.
C239235C11
0.146,0.802 0.542,1.052 0.396,0.25 0.229,0.844 0.688,1.042 0.458,0.198 10 false d16 0.083,0.073 0.542,0.271 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Occupant Detection ECU)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d16-1 - Body ground Always 11 to 14 V
d16-6 - Body ground Ignition switch ON



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

REPLACE HARNESS OR CONNECTOR

5.CHECK DTC
a.

Connect the connector to the occupant detection ECU.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1794 is not output
DTC B1794 is output


HINT:

DTCs other than DTC B1794 may be output at this time, but they are not related to this check.




DTC B1794 is not output

DTC B1794 is output

6.REPLACE OCCUPANT DETECTION ECU
6.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



Result:
Proceed to
NEXT



NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

8.PERFORM SENSITIVITY CHECK
8.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)