50819
1.REMOVE FRONT FLOOR COVER
Remove the bolt and nut.
Detach the 5 clips and remove the front floor cover.
77641A
2.REMOVE NO. 1 FUEL TANK PROTECTOR
Detach the 3 clips and remove the nut and No. 1 fuel tank protector.
58398F
3.REMOVE NO. 1 FLOOR UNDER COVER
Detach the clip and remove the 2 nuts and No. 1 floor under cover.
46420
4.DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY
Remove the 2 bolts and disconnect the No. 2 parking brake cable assembly.
77204A
5.DISCONNECT FUEL TANK RETURN TUBE
Slide the clamp and disconnect the fuel tank return tube from the fuel pipe.
77209D
6.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>PRECAUTION
77213E
7.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
77269A
8.DISCONNECT FUEL TANK BREATHER HOSE
Disconnect the fuel tank breather hose from the fuel tank assembly.
Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>PRECAUTION
77100
9.REMOVE FUEL TANK ASSEMBLY
Set an engine lifter underneath the fuel tank assembly.
Disconnect the wire harness from the 2 fuel tube grommets.
Remove the 2 bolts and No. 1 fuel tank band sub-assembly.
Remove the 2 bolts and No. 1 fuel tank band sub-assembly LH.
Remove the 2 bolts and No. 2 fuel tank band sub-assembly.
Slightly lower the engine lifter.
Be careful not to cut the wire harness.
Disconnect the fuel sender gauge connector and remove the fuel tank assembly.
Before this procedure, check the connector for dirt, mud or other contamination.
Do not use any tools in this procedure.
77249
10.REMOVE FUEL EMISSION HOSE
Detach the clamp and remove the fuel emission hose.
Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>PRECAUTION
77209D
11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Remove the tube joint clip and pull out the fuel tank main tube sub-assembly.
Before removing a tube joint clip, check for foreign matter around the tube joint clip. Clean if necessary.
Do not use any tools in this procedure.
Do not forcefully bend or twist the fuel tank main tube sub-assembly.
Put the fuel tank main tube sub-assembly in a plastic bag to prevent damage and contamination.
If the fuel tank vent tube assembly and fuel tank main tube sub-assembly are stuck together, pinch the fuel tank main tube sub-assembly and turn it carefully to disconnect it.
Be careful not the damage any tube joint clip. If a tube joint clip is damaged, replace it.
77204A
12.DISCONNECT FUEL TANK RETURN TUBE
Remove the tube joint clip and pull out the fuel tank return tube.
Before removing a tube joint clip, check for foreign matter around the tube joint clip. Clean if necessary.
Do not use any tools in this procedure.
Do not forcefully bend or twist the fuel tank return tube.
Put the fuel tank return tube in a plastic bag to prevent damage and contamination.
If the fuel tank vent tube assembly and fuel tank return tube are stuck together, pinch the fuel tank return tube and turn it carefully to disconnect it.
Be careful not the damage any tube joint clip. If a tube joint clip is damaged, replace it.
77168A
13.REMOVE FUEL TANK VENT TUBE SET PLATE
Remove the 8 bolts and fuel tank vent tube set plate.
77010
14.REMOVE FUEL TANK VENT TUBE ASSEMBLY
Slide the 2 clamps, disconnect the 2 fuel hoses and remove the fuel tank vent tube assembly.
Do not damage the fuel tank vent tube assembly.
Remove the gasket from the fuel tank vent tube assembly.
77209D
15.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Remove the fuel tank main tube sub-assembly from the No. 5 fuel tube clamp and 3 fuel tube grommets.
77204A
16.REMOVE FUEL TANK RETURN TUBE
Remove the fuel return tube from the No. 5 fuel tube clamp and 3 fuel tube grommets.
77299A
17.REMOVE NO. 5 FUEL TUBE CLAMP
Remove the No. 5 fuel tube clamp from the fuel tank assembly.
77295D
18.REMOVE FUEL TUBE GROMMET
Remove the 3 fuel tube grommets from the fuel tank assembly.
83320
19.REMOVE FUEL SENDER GAUGE ASSEMBLY