Home › Drivetrain › EB63F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _009273 EB63F MANUAL TRANSMISSION / TRANSAXLE _0050748 DIFFERENTIAL CASE A

EB63F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41039A 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C02
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Center Differential Side Gear Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

Gear Oil


Coat the front differential side gear, front No. 1 differential side gear thrust washer and center differential side gear conical spring washer with gear oil.


b.
C318270C01
1.542,2.896 1.74,2.896 1.74,2.896 2.271,2.604 true 1.719,1.052 1.917,1.052 1.917,1.052 2.271,1.219 true 1.698,0.885 1.896,0.885 1.896,0.885 2.25,1.052 true 1.74,2.479 1.938,2.479 1.938,2.479 2.24,2.281 true 1.573,3.156 1.771,3.156 1.771,3.156 2.313,2.771 true 1.625,1.396 1.823,1.396 1.823,1.396 2.177,1.563 true 1.427,1.333 1.74,1.531 0.313,0.198 10 true *1 1.479,0.99 1.792,1.188 0.313,0.198 10 false *2 1.479,0.792 1.792,0.99 0.313,0.198 10 false *3 1.354,2.823 1.667,3.021 0.313,0.198 10 false *2 1.385,3.083 1.698,3.281 0.313,0.198 10 false *3 1.469,2.385 1.781,2.583 0.313,0.198 10 true *1
*1 Front Differential Side Gear
*2 Center Differential Side Gear Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 center differential side gear conical spring washers to the front differential case.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and center differential side gear conical spring washer.

·

Make sure that the center differential side gear conical spring washer is installed in the correct direction.




c.

Set SST as shown in the illustration and tighten it.

SST
09528-52010  (09528-05010, 09953-05010)

C318268C01
4.677,0.281 5.198,0.281 false 5.135,1.438 3.802,1.656 3.802,1.656 5.146,1.219 true 3.135,0.229 3.448,0.427 0.313,0.198 10 false *a 1.115,2.198 1.427,2.396 0.313,0.198 10 false *b 4.281,0.208 4.688,0.438 0.406,0.229 10 false SST 3.458,1.594 3.865,1.823 0.406,0.229 10 false SST
*a Turn *b Hold


NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, center differential side gear conical spring washer, front No.1 differential side gear thrust washer and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C287727C01
0,0 0,0 false
V100135

Gear Oil


Coat the front differential pinion and front differential pinion thrust washer with gear oil.


e.
C318275C01
1.813,1.458 2.156,1.458 2.156,1.458 2.458,2.073 true 1.344,0.667 1.656,0.865 0.313,0.198 10 false *a 1.438,1.375 1.896,1.573 0.458,0.198 10 false SST
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C318276C01
0,0 0,0 false
V100135

Gear Oil


Coat a front No. 1 differential pinion shaft with gear oil.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41311 4.INSPECT FRONT DIFFERENTIAL CASE

Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C318277

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C318278

Using a chisel and hammer, stake the front differential case.


Hide 41221 6.INSTALL FRONT DIFFERENTIAL RING GEAR

a.

Clean the contact surfaces of the front differential case and front differential ring gear.


b.

Using a heater, heat the front differential ring gear to 90 to 100°C (194 to 212°F).


c.
C207064C02
1.99,0.49 1.208,0.167 false 1.208,0.167 0.5,0.167 false 1.927,0.667 1.208,0.167 false 0.26,0.083 0.51,0.271 0.25,0.188 10 *a
*a Matchmark


After the moisture on the front differential ring gear has completely evaporated, quickly align the matchmarks on the front differential ring gear and front differential case and install the front differential ring gear to the front differential case.


d.
C199117

Install the 12 bolts.

Torque:
106 N*m (1081 kgf*cm, 78 ft.*lbf)


Hide 41311R 7.INSTALL FRONT DIFFERENTIAL CASE OIL SEAL

a.

Coat the lip of a new front differential case oil seal with MP grease.


b.
C204253C01
0.458,1.385 0.698,1.385 false 2.594,0.938 2.865,0.938 false 2.573,1.031 2.75,1.031 false 2.75,1.031 2.75,0.938 false 0.073,1.302 0.375,1.448 0.302,0.146 10 SST 2.885,0.854 3.188,1 0.302,0.146 10 SST 1.573,0.875 1.833,1.104 0.26,0.229 10 *a
*a 21.5 to 22.5 mm (0.847 to 0.885 in.)


Using SST and a hammer, tap in a new front differential case oil seal to the front differential case.

SST
09950-60010  (09951-00330, 09951-00410, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

21.5 to 22.5 mm (0.847 to 0.885 in.)


NOTICE:

Do not damage the front differential case oil seal lip.