Home › Drivetrain › EB61 MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008757 EB61 MANUAL TRANSMISSION / TRANSAXLE _0048571 DIFFERENTIAL CASE G

EB61 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  INSPECTION  


PROCEDURE

Hide 41302F 1.INSPECT FRONT DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C288233N02
0.906,1.042 1.198,1.042 1.198,1.042 1.646,1.302 true 0.615,0.969 1.073,1.167 0.458,0.198 10 false SST

Using SST, rotate the front differential side gear as shown in the illustration.

SST
09528-52010  (09528-05030)

Standard:

The front differential side gear does not lock when rotated in either direction.


·

If the front differential side gear locks, perform all remaining inspection procedures.


·

Replace any parts that do not meet the specifications.


·

If the front differential side gear locks after performing the inspection procedures, replace the front differential case assembly.



Hide 2.INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT

a.
C288439C01
0.583,0.74 0.76,0.74 0.76,0.74 1.24,1.219 true 2.646,2.99 2.958,3.146 0.313,0.156 10 false *a 0.292,0.667 0.75,0.865 0.458,0.198 10 false SST
*a Front Differential Side Gear Thrust Amount


Using SST and a dial indicator, measure the thrust amount of the front differential side gear.

SST
09528-52010  (09528-05030)

Front Differential Side Gear Thrust Amount:

0.08 mm (0.00314 in.) or less


HINT:
·

Measure the front differential side gear thrust amount while slowly rotating the front differential side gear.

·

Make sure to measure the front differential side gear thrust amount for both of the front differential side gears.



If the result is not as specified, replace the 2 center differential side gear conical spring washers, 2 front differential side gears and 2 front differential pinions.


Hide 3.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

a.

Set SST as shown in the illustration and tighten it.

SST
09528-52010  (09528-05010, 09953-05010)

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C288646C01
4.594,0.417 5.042,0.417 false 4.979,1.771 4.417,1.646 4.417,1.646 4.979,1.51 true 2.854,0.563 3.167,0.719 0.313,0.156 10 false *a 0.5,2.188 0.813,2.344 0.313,0.156 10 false *b 4.281,0.344 4.74,0.542 0.458,0.198 10 false SST 4.115,1.563 4.573,1.76 0.458,0.198 10 false SST
*a Turn *b Hold



b.
C301362C01
1.844,0.313 2.302,0.313 true 1.615,0.24 1.927,0.438 0.313,0.198 10 false *1
*1 Front No. 1 Differential Pinion Shaft


Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.


c.

Using a dial indicator, measure the front differential pinion backlash.

Standard Backlash:

0.20 mm (0.00787 in.) or less


If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.

Front No. 1 Differential Side Gear Thrust Washer Thickness:
Mark Specified Condition
1 1.00 mm (0.0394 in.)
2 1.10 mm (0.0433 in.)
3 1.20 mm (0.0472 in.)
4 1.30 mm (0.0512 in.)


HINT:

Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.



Hide 41351F 4.INSPECT FRONT DIFFERENTIAL PINION THRUST WASHER

a.
C288044

Using a micrometer, measure the thickness of the front differential pinion thrust washer.

Minimum Thickness:

0.9 mm (0.0354 in.)


If the thickness is less than the minimum, replace the front differential pinion thrust washer.


Hide 41342F 5.INSPECT FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C291384C01
2.542,0.823 2.854,1.021 0.313,0.198 10 false *a
*a Outer Diameter


Using a micrometer, measure the outer diameter of the front No. 1 differential pinion shaft.

Minimum Outer Diameter:

17.975 mm (0.708 in.)


If the outer diameter is less than the minimum, replace the front No. 1 differential pinion shaft.