Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) D

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  SYSTEM DESCRIPTION  


STOP AND START CONTROL


The stop and start system operates according to the following conditions, achieving appropriate engine stop and start control together with safe and smooth driving characteristics.

a.

When all of the conditions in the following table have been met, the engine is stopped by stop and start control.

Item Condition
(All of the following conditions are met)
Idle Stop Ignition Switch 5 seconds or more have passed with the ignition switch ON
Engine Coolant Temperature 40 to 105°C (104 to 221°F)
Ambient Temperature Higher than -5°C (23°F)
Driver Door 3 seconds have elapsed after driver door closed
Driver Seat Belt 3 seconds have elapsed after driver seat belt fastened
Vehicle Stability Control System Normal
Brake Booster Vacuum Sufficient
Brake Master Cylinder Fluid Pressure 1.5 MPa (15.2 kg/cm2, 2.2 psi) (changes according to gradient)
Shift Position After shift lever is operated and 1 second elapses, shift lever is in position other than P, N or R
CVT Oil Temperature 25 to 111°C (77 to 231.8°F)
Stop and Start System Cancel Switch (Ecorun Cancel Switch Assembly) Off (System control is not prohibited)
Vehicle Speed 0 km/h (0 mph) (After the engine warms up)
Road Grade -8° to +8°
Engine Speed 1250 rpm or less
Hood 3 seconds have elapsed after hood closed
Battery Voltage
When using specified battery:

Higher than 7.65 V when starter begins operation and higher than 7.66 V when cranking


When using non-specified battery:

Higher than 8.92 V when starter begins operation and higher than 8.92 V when cranking


Battery Temperature*1 -10 to 70°C (14 to 158°F)
Battery Integrated Current*2
1.

0 A-sec or higher: After engine started by ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) operation

2.

Integrated current value has increased to 0 A-sec or higher at least once after ignition switch ON:

HINT:
Engine is stopped until the following conditions are not met:
·

Higher than -13478 A-sec: "Status of Battery Charge Control"*3 is Charge Control Coordination Mode or Stop and Start Standalone Mode

·

Higher than -6048 A-sec: "Status of Battery Charge Control"*3 is Low Temperature Mode and "Battery Fulid Temperature" is between 3°C (37.4°F) and 11°C (51.8°F)

·

Higher than -3974 A-sec: "Status of Battery Charge Control"*3 is Low Temperature Mode and "Battery Fulid Temperature" is between -1°C (30.2°F) and under 3°C (37.4°F)

·

Higher than 0 A-sec: "Status of Battery Charge Control"*3 is Stop and Start Restriction Mode or Temperature High/Low Mode




Air Conditioning Other than when stop and start control is prohibited
Heater
One of the following conditions is met:
·

Blower switch is off

·

Blower switch is on when the ambient temperature is higher than 10°C (50°F), the engine coolant temperature is higher than 55°C (131°F) or the room temperature is 5°C (41°F) lower than the set temperature

·

Blower switch on, air conditioning switch off and a certain amount of time has elapsed after engine restarted by stop and start control


Steering Operation 45 deg/s or less

HINT:
·

*1: When the battery temperature is below -15°C (5°F), or 75°C (167°F) or higher, stop and start control is prohibited. When the battery temperature returns to -10°C (14°F) or higher, or below 70°C (158°F), stop and start control is permitted.

·

*2: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DATA LIST / ACTIVE TEST

·

*3: Please refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.




b.

When the engine is stopped by stop and start control, and any of the following conditions are met, the engine will restart.

Item Condition
(Any of the following conditions is met)
Engine Restart Brake Booster Vacuum Brake booster vacuum insufficient (Brake booster vacuum changes in accordance with brake fluid pressure (brake pedal effort))
Engine Hood Courtesy Switch (Hood Lock Assembly) Engine hood courtesy switch (hood lock assembly) malfunctioning
SFI System Malfunction in SFI system is detected
Oil Pump Assembly with Motor Oil pump assembly with motor (continuously variable transaxle assembly) malfunctioning
Power Steering System Malfunction in power steering system is detected
Vehicle Stability Control System Malfunction in vehicle stability control system is detected
Air Conditioning Timer in the air conditioning amplifier assembly runs out
Heater Timer in the air conditioning amplifier assembly runs out
Air Conditioning/Heater
Both of the following conditions are met:
·

Blower switch: ON

·

Evaporator temperature exceeds threshold value (threshold value varies with temperature, humidity and amount of solar radiation)


Any of the following conditions are met:
·

A/C switch, blower switch: ON

·

Defogger switch: ON

·

Blower switch turned off during auto control or blower mode changed to manual


Battery Battery performance or voltage drops
Battery Integrated Current*1
·

-14342 A-sec or less: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Stop and Start Standalone Mode

·

-6912 A-sec or less: "Status of Battery Charge Control"*2 is Low Temperature Mode and "Battery Fluid Temperature" is between 3°C (37.4°F) and 11°C (51.8°F)

·

-4838 A-sec or less: "Status of Battery Charge Control"*2 is Low Temperature Mode and "Battery Fluid Temperature" is between -1°C (30.2°F) and under 3°C (37.4°F)

·

-864 A-sec or less: "Status of Battery Charge Control"*2 is Stop and Start Restriction Mode or Temperature High/Low Mode


Vehicle Speed Vehicle speed signal is input (Vehicle stopped on a slope, etc.)
Driver Door Open
Driver Seat Belt Driver seat belt is unfastened
Steering Wheel Steering wheel turned 25 deg or more
Brake Master Cylinder Fluid Pressure Brake pedal released (brake fluid pressure decreases) or 10 MPa (102 kgf/cm2, 1450 psi) or higher
Accelerator Pedal Accelerator pedal is depressed

HINT:
·

*1: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DATA LIST / ACTIVE TEST

·

*2: Please refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.





SYSTEM PROHIBITION CONTROL


The engine stop and start ECU prohibits stop and start control by the stop and start system according to the table below. The prohibition conditions are specified for each system.

System Prohibition Condition Vehicle State Restoration Condition Prohibition Condition Check Timing
Engine Engine coolant temperature less than 40°C (104°F) Engine has not warmed up Engine coolant temperature 40 between 105°C (104°F to 221°F) Always
Idle speed learning has not completed Stop and start control prohibited until idle speed learning completes Idle speed learning has completed Always
Brake Brake booster vacuum decreases Brake booster vacuum decreases due to pumping the brakes, etc. Normal brake booster vacuum is reached Every time the vehicle stops
Brake master cylinder fluid pressure decreases Brake pedal depressed lightly Brake pedal depressed more Every time the vehicle stops
Hill-start Assist Control Brake control system malfunction DTC detected Brake control system returns normally Always
When hill-start assist control prohibition is necessary Vehicle speed is 3 km/h (1.8 mph) or more Vehicle is being stopped (vehicle speed is below 3 km/h (1.8 mph)) Always
Communication between engine stop and start ECU and skid control ECU (brake actuator assembly) is invalid Communication invalid Communication between engine stop and start ECU and skid control ECU (brake actuator assembly) is valid Always
Gradient of Road Surface Outside the permission gradient range (vehicle front and rear road surface incline +8° or higher or -8° or lower) Vehicle front and rear road surface incline +8° or higher or -8° or lower Within the permission gradient range (vehicle front and rear road surface incline within +/-8°) Always
Air Conditioning Heater:
All of the following conditions are met:
·

Blower switch on and A/C switch on

·

Ambient temperature 10°C (50°F) or less

·

Engine coolant temperature 55°C (131°F) or less


Heater performance decreases
·

Actual temperature higher than target temperature

·

Blower switch off


While the heater is on
Cooling function:
When blower switch and A/C switch are on and ambient temperature 23°C (73.4°F) or higher, the following condition is met (only when the ignition switch is first turned to ON):
·

Evaporator temperature 9°C (48.2°F) or higher


Cooling performance decreases
Any of the following conditions have been met:
·

Actual temperature higher than target temperature

·

Blower switch is off

·

Air conditioning switch is off


While the air conditioning system (cooling function) is on
Defogger:
Any of the following conditions are met:
1.

Defogger switch or blower switch on

2.

A certain amount of time after the engine is restarted by stop and start control when the ambient temperature is 10°C (50°F) or lower and the blower switch is on.


1.

Fogging of windows

2.

Air conditioning performance decreases

3.

Odor from air vents


Any of the following conditions are met:
1.

Defogger switch or blower switch off

2.

A certain amount of time has elapsed after restarting the engine by stop and start control

3.

A certain amount of time has elapsed or the air conditioning switch is off after restarting the engine by the stop and start control


While the air conditioning system (cooling function for defogger) is on
Temporary start and start control:
Both of the following conditions are met:
·

Blower switch on

·

Evaporator temperature exceeds threshold (threshold varies with temperature, humidity and amount of solar radiation)


Blower switch on Blower switch off and evaporator temperature within specified range Always
Driver Door Driver door opened before engine stop by engine stop and start control Driver door courtesy switch ON signal input 3 seconds have elapsed since driver door was closed Always
Engine Hood Engine hood opened before engine stop by stop and start control Engine hood switch OFF signal input 3 seconds have passed since engine hood was closed Always
Seat Belt Driver seat belt not fastened before engine stop by engine stop and start control Driver seat belt buckle switch OFF signal input 3 seconds have passed since driver seat belt was fastened Always
Steering Wheel Steering wheel turned at a speed of 45 deg/s or more Steering wheel operation signal input Steering wheel being held Always
CVT CVT oil temperature lower than 25°C (77°F) or 111°C (231.8°F) or higher CVT Oil Temperature signal is input An appropriate CVT fluid temperature is reached Always
Shift Position Shift lever in P, N or R Shift position signal input Brake pedal depressed and shift lever in D or M Always
Ambient Temperature Ambient temperature -6°C (21.2°F) or lower - Ambient temperature -5°C (23°F) or higher Always
Power Source
When using specified battery:

Higher than 7.65 V when starter begins operation and higher than 7.66 V when cranking


When using non-specified battery:

Higher than 8.92 V when starter begins operation and higher than 8.92 V when cranking


Battery charge insufficient or battery has deteriorated Battery charged or replaced Every time the engine started
Battery temperature below -15°C (5°F) or 75°C (167°F) or higher Depends on Ambient temperature An appropriate battery temperature is reached (between -10 and 70°C (14 to 158°F)) Always
Battery integrated current*1 value meets one of the following conditions:
1.

Below 0 A-sec: After engine start by ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) operation

2.

Any of the following conditions are met:

·

-14342 A-sec or less: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Stop and Start Standalone Mode

·

-6912 A-sec or less: "Status of Battery Charge Control"*2 is Low Temperature Mode and "Battery Fluid Temperature" is between 3°C (37.4°F) and 11°C (51.8°F)

·

-4838 A-sec or less: "Status of Battery Charge Control"*2 is Low Temperature Mode and "Battery Fluid Temperature" is between -1°C (30.2°F) and under 3°C (37.4°F)

·

-864 A-sec or less: "Status of Battery Charge Control"*2 is Stop and Start Restriction Mode or Temperature High/Low Mode



·

Heavy electrical load

·

High stop and start rate (Time that engine stopped by stop and start control is long)


Battery integrated current*1 value meets both of the following conditions:
1.

0 A-sec or higher: After engine start by ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System) operation

2.

Any of the following conditions are met:

·

-13478 A-sec or higher: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Stop and Start Standalone Mode

·

-6048 A-sec or higher: "Status of Battery Charge Control"*2 is Low Temperature Mode and "Battery Fluid Temperature" is between 3°C (37.4°F) and 11°C (51.8°F)

·

-3974 A-sec or higher: "Status of Battery Charge Control"*2 is Low Temperature Mode and "Battery Fluid Temperature" is between -1°C (30.2°F) and under 3°C (37.4°F)

·

0 A-sec or higher: "Status of Battery Charge Control"*2 is Stop and Start Restriction Mode or Temperature High/Low Mode



Always
During refresh charge
·

Cable reconnected to negative (-) battery terminal

·

Refresh charge is performed for 30 minutes or longer for every 30 hours of driving


30 minutes to 1 hour has elapsed Always
Engine started with the engine hood open (for jump starting) - After ignition switch is turned off, ignition switch is turned to ON with hood closed Every time the engine started
Idling Stop Rate Idling stop rate for one trip is 50% and total idling stop rate is 40% Vehicle is stopped for long time Idling stop rate has decreased due to vehicle being driven and engine idling Always

HINT:
·

*1: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value

·

*2: Please refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.

·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.




WARNING CONTROL


If any of the following operations are performed while the engine is stopped due to stop and start control, the system will not restart the engine. The engine will change the mode from "stopped due to system control" to "stalled" or the driver will be warned using the buzzer.

Operation Warning Control
The engine hood is opened with the shift lever in D or M The engine stops (mode changes to "stalled", and the engine cannot be restarted until the ignition switch is turned off and then to ON)
The driver door is opened with the shift lever in D or M The engine starts, warning buzzer sounds and stop and start indicator light blinks
The driver seat belt is unfastened The engine starts


WARNING INDICATOR AND BUZZER OPERATION


A287227C01
0.677,0.271 1.031,0.583 0.354,0.313 10 *a 0.677,1.729 1.031,2.042 0.354,0.313 10 *b
*a Stop and Start Indicator Light
*b Stop and Start Cancel Indicator Light


The driver is informed of the system control status and warnings by the stop and start indicator light, stop and start cancel indicator light and the buzzer.

Stop and Start Indicator and Buzzer Operation
Item Condition Stop and start indicator light Stop and start cancel indicator light Buzzer
For 3 seconds after the ignition switch ON Normal operation Comes on Comes on Does not sound
During stop and start control operation (engine is stopped) Normal operation Comes on Does not come on Does not sound
Driver door opened The blinking interval 0.15 seconds* Does not come on Sounds*
After engine started by stop and start control Driver door opened within 5 seconds of engine start The blinking interval 0.15 seconds* Does not come on Sounds*
Control is prohibited by the stop and start system cancel switch (ecorun cancel switch assembly) Normal operation Does not come on Comes on Does not sound
Diagnostic trouble code Any DTCs are stored Does not come on Blinks at 0.5 second intervals. Does not sound
Starter assembly life Number of times the starter has been operated exceeds its limit Does not come on Blinks at 0.5 second intervals. Does not sound

*: Shift lever in D or M



STOP AND START SYSTEM OPERATION


Depending on the type of malfunction, stop and start control may be prohibited by the fail-safe function. The following table shows effects on the vehicle and areas to be inspected when there is a malfunctions in the stop and start system.

Malfunctioning Area Malfunction DTC Output Data List / Freeze Frame Data Effect on Vehicle Area to be Inspected
IGSW circuit Open P2531
·

IG Switch

·

IG SW Abnoml


Stop and start control prohibited Wire harness or connector
+B circuit Open - Data List cannot be checked because power not supplied to the engine stop and start ECU Stop and start control prohibited Wire harness or connector
CLL (park/neutral position switch assembly) circuit Stuck on P1780
·

Neutral Switch

·

Neutral Switch Stuck ON

·

Neutral SW Abnoml (ON)


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Park/neutral position switch assembly


Stuck off P1780
·

Neutral Switch

·

Neutral Switch Stuck OFF

·

Neutral SW Abnoml (OFF)


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


BNT1 (engine hood courtesy switch) circuit Stuck on - Hood Courtesy Switch Mode does not change to "stalled" when engine hood opened with shift lever in D or M and engine stopped by stop and start control
·

Wire harness or connector

·

Engine hood courtesy switch (Hood lock assembly)


Stuck off - Hood Courtesy Switch Stop and start control prohibited despite engine hood being closed
BRVC/PB/BRE2 (vacuum sensor) circuit Open P1540
·

Brk Boost Sen Abnoml 1

·

Brk Boost Sen Abnoml 2

·

Brk Boost Sen Abnoml 3


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Vacuum sensor assembly

·

Brake booster assembly

·

Check valve to connector tube hose


Shorted P1540
Remains at intermediate value P1541
ECAN (stop and start system cancel switch (ecorun cancel switch assembly)) circuit Stuck on - Cancel Switch Stop and start control prohibited
·

Wire harness or connector

·

Stop and start system cancel switch (ecorun cancel switch assembly)


Stuck off - Cancel Switch Stop and start control cannot be canceled by pressing the stop and start system cancel switch (ecorun cancel switch assembly)
NOPM circuit
OPM1 circuit
OPO circuit
(CVT oil pump assembly with motor)
·

Open

·

Shorted

·

Internal circuit malfunction

·

Battery


P1538
P1539
·

Oil Pump Relay

·

Oil Pump Status

·

Oil Pump Duty

·

State of Oil Pump Motor Rotation

·

Oil Pump Motor Rotation Frequency

·

Oil Pump Abnormality Judgment

·

Status of O/P Signal 1

·

Status of O/P Signal 2


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Engine stop and start ECU

·

Oil pump assembly with motor (continuously variable transaxle assembly)


CVT oil pump assembly with motor Oil pump assembly with motor malfunction P0942 Oper Permission(AT/CVT) Stop and start control prohibited
·

Oil pump assembly with motor (continuously variable transaxle assembly)


STA circuit Overcurrent P0617
·

Starter Relay Overcurrent

·

Starter Circuit Abnoml

·

Starter Circuit Open


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

ST NO. 1 relay

·

ST NO. 2 relay

·

Engine stop and start ECU


Stuck on P1644
·

Wire harness or connector

·

ST NO. 1 relay

·

ST NO. 2 relay

·

Engine stop and start ECU


Stuck off P1644
BBC (backup boost converter) circuit Overcurrent B22C0
·

State of BBC

·

BBC Abnoml

·

BBC Overcurrent

·

BBC Check Result


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Battery

·

ECUs and sensors connected to BO1 and IGO1


·

Open

·

Shorted

·

Internal circuit malfunction

·

Battery


P323B
·

State of BBC

·

BBC Duty

·

BBC Thermistor

·

BBC Abnoml

·

BBC Over Heat

·

BBC Power Low


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Battery


VB- circuit Open P0560 VB Voltage Low
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Engine stop and start ECU


ECU inner circuit Malfunction P0607 -
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
Monitoring CPU circuit Malfunction P060A State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
EEPROM Malfunction P062F EEPROM
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
Sensor power source circuit Malfunction P0641 State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU
Starter delay circuit Malfunction P161D
·

Pinion Gear

·

Starter Motor

·

Starter Delay Circuit


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Engine stop and start ECU

Effects on Vehicle due to Related System Malfunctions
Malfunctioning Area Malfunction DTC Output Data List / Freeze Frame Data Effect on Vehicle Area to be Inspected
SFI system MIL illuminated DTCs for SFI system output
·

Oper Permission (ECM 1)

·

Oper Permission (ECM 2)


Stop and start control prohibited SFI system
Abnormal NE signal DTCs for SFI system output
·

NE Sensor Circuit Open 2

·

Crank Pos Sen Abnoml 3


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

SFI system (crank position sensor circuit)

·

Wire harness or connector


Crankshaft reverse rotation detection DTCs for SFI system output -
·

Stop and start control prohibited

·

MIL illuminated


SFI system (crank position sensor circuit)
Charging system Battery state sensor assembly malfunction DTCs for charging system output
·

Battery Fluid Temperature

·

Integrated Current


Stop and start control prohibited Charging system
Vehicle stability control system VSC Running - ABS Running Stop and start control prohibited -
Malfunction in wheel speed sensor Brake control system DTCs output
·

Vehicle Spd1 (ABS/VSC)

·

Wheel Speed Malfunction


Stop and start control prohibited
·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Vehicle speed sensor


Power steering system Malfunction in power steering system EPS assist current value invalid
·

EPS Load

·

Comm Err with EPS


Stop and start control prohibited
·

Power steering ECU assembly

·

Torque sensor


Seat belt warning system Malfunction in seat belt warning system - Oper Permission (Driver Side Buckle SW)
·

Stop and start control prohibited (stuck off)

·

Engine does not restart when it is stopped by stop and start control (stuck on)


·

Front seat inner belt assembly (for driver side)

·

Wire harness or connector


Driver door courtesy light switch circuit Malfunction in driver door courtesy light switch circuit - D Courtesy Switch Signal
·

Stop and start control prohibited (stuck off)

·

Engine does not restart when it is stopped by stop and start control (stuck on)


·

Front door courtesy light switch assembly (for driver side)

·

Driver door courtesy light switch circuit


Air conditioning system Malfunction in ambient temperature sensor Air conditioning system DTCs output Ambient Temp Sensor Stop and start control prohibited Ambient temperature sensor circuit
Brake vacuum Brake booster vacuum drops -
·

Brake Boost Pressure

·

Brake Negative Pressure

·

Brk Boost Sen Abnoml 1

·

Brk Boost Sen Abnoml 2

·

Brk Boost Sen Abnoml 3


Stop and start control prohibited
·

Brake booster assembly vacuum

·

Brake booster assembly

·

Vacuum sensor assembly

·

Check valve to connector tube hose


Power source Backup boost converter malfunction P323B
·

State of BBC

·

BBC Duty

·

BBC Thermistor

·

BBC Abnoml

·

BBC Over Heat

·

BBC Power Low


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

BBC fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Battery


Charging system malfunction - Alternator Status Stop and start control prohibited Charging system
Low voltage P0562 Battery Abnoml
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Battery

·

Relay


Number of starter operations Exceeds the specified limit P1545 Starter Count Abnoml
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Starter assembly replacement is required.

·

ST NO. 2 relay replacement is required.

·

Fuse replacement is required.


Starter signal malfunction Signal does not match with the starter switch P1545 -
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Engine stop and start ECU


Jump start Engine started with the engine hood open - Eng Start Req (Engine Hood Open) Stop and start control prohibited
(permitted when the ignition switch is turned off)
·

Check for history of roadside service or jump start due to dead battery

·

Engine hood courtesy switch (Hood lock assembly)


CAN communication Communication interrupted U0100
U0121
U0126
U0131
U0140
U0151
U0155
U0164
-
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Applicable wire harness or connector

·

Applicable ECU