Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) U

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  TERMINALS OF ECU  


ENGINE STOP AND START ECU


A348145E01
0.594,2.125 1.115,2.344 0.521,0.219 1.458,0.198 1.979,0.417 0.521,0.219 2.594,2.115 3.115,2.333 0.521,0.219 5.344,2.115 5.865,2.333 0.521,0.219 3.104,0.198 3.625,0.417 0.521,0.219 4.958,0.198 5.479,0.417 0.521,0.219 0.719,2.156 1.031,2.333 0.313,0.177 10 false A65 1.594,0.229 1.906,0.406 0.313,0.177 10 false A65 2.729,2.156 3.188,2.354 0.458,0.198 10 false A66 3.24,0.24 3.698,0.438 0.458,0.198 10 false A66 5.094,0.229 5.552,0.427 0.458,0.198 10 false G87 5.479,2.146 5.938,2.344 0.458,0.198 10 false G87

a.

Disconnect the A65, A66 and G87 engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A65-5 (+B) - Body ground B - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
A65-7 (BIN) - Body ground L - Body ground Battery Always 9.5 to 14 V
A65-8 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A66-10 (NE) - Body ground P - Body ground Engine speed signal from ECM Always 10 kΩ or higher
A66-17 (VB-) - Body ground W-B - Body ground Ground Always Below 1 Ω
G87-15 (CANH) - Body ground LG - Body ground CAN communication Always 200 Ω or higher
G87-16 (CANL) - Body ground W - Body ground CAN communication Always 200 Ω or higher
G87-17 (IG1) - Body ground L - Body ground Ignition or starter switch assembly*1 or push start switch assembly*2 signal Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - Body ground W - Body ground Ignition or starter switch assembly*1 or push start switch assembly*2 signal Ignition switch ACC 9.5 to 14 V
G87-20 (IG2) - Body ground V - Body ground Ignition or starter switch assembly*1 or push start switch assembly*2 signal Ignition switch ON 9.5 to 14 V

*1: w/o Entry and Start System

*2: w/ Entry and Start System



c.

Reconnect the A65, A66 and G87 engine stop and start ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A65-6 (OPO) - A65-8 (GND) G - W-B Oil pump assembly with motor (continuously variable transaxle assembly) drive power source signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed


10.5 to 16 V
A66-3 (BRE2) - Body ground G - Body ground Ground (vacuum sensor assembly (brake booster pressure sensor)) Always Below 1 Ω
A66-7 (BNT1) - A65-8 (GND) R - W-B Engine hood courtesy switch (Hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


0 to 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
A66-9 (OPM1) - A65-8 (GND) LG - W-B Oil pump assembly with motor (continuously variable transaxle assembly) directions signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed


Pulse generation
(see waveform 1)
A66-10 (NE) - A65-8 (GND) P - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform 2)
A66-13 (PB) - A66-3 (BRE2) B - G Vacuum sensor assembly (Brake booster pressure sensor) signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied to vacuum sensor assembly (brake booster pressure sensor)


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (450 mmHg, 17.7 in.Hg) applied to vacuum sensor assembly (brake booster pressure sensor)


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly (brake booster pressure sensor)


3.4 to 3.8 V
A66-14 (BRVC) - A65-8 (GND) P - W-B Vacuum sensor assembly (Brake booster pressure sensor) power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A66-21 (STA) - A65-8 (GND) LG - W-B Starter pinion operation signal Cranking 6.0 V or more
A66-23 (STA2) - A65-8 (GND) V - W-B Starter motor operation signal Cranking 6.0 V or more
A66-27 (NOPM) - A65-8 (GND) W - W-B Oil pump assembly with motor (continuously variable transaxle assembly) speed signal Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed


Pulse generation
(see waveform 3)
A66-28 (CLL) - A65-8 (GND) W - W-B Park/neutral position switch assembly signal
·

Ignition switch ON

·

Shift lever not in P or N


8 to 14 V
·

Ignition switch ON

·

Shift lever in P or N


Below 3.0 V
G87-2 (BO1) - A65-8 (GND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
G87-3 (ACO) - A65-8 (GND) GR - W-B Backup boost converter signal Ignition switch ACC 10.5 to 16 V
G87-11 (IGO2) - A65-8 (GND) P - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-12 (IGO1) - A65-8 (GND) L - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
G87-17 (IG1) - A65-8 (GND) L - W-B Ignition or starter switch assembly*1 or push start switch assembly*2 signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-19 (ACC) - A65-8 (GND) W - W-B Ignition or starter switch assembly*1 or push start switch assembly*2 signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
G87-20 (IG2) - A65-8 (GND) V - W-B Ignition switch signal
Ignition or starter switch assembly*1 or push start switch assembly*2 signal
Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
G87-23 (ECAN) - A65-8 (GND) V - W-B Stop and start system cancel switch (Ecorun cancel switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (Ecorun cancel switch assembly) pressed


0 to 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (ecorun cancel switch assembly) not pressed


8 to 14 V

*1: w/o Entry and Start System

*2: w/ Entry and Start System



e.
A329962E01
0.073,0.052 1.302,0.25 1.229,0.198 10 false 5 V/DIV. 1.135,2 1.958,2.177 0.823,0.177 10 false 5 ms./DIV. 2.885,1.25 3.344,1.448 0.458,0.198 10 false GND

Waveform 1

Item Content
Tester Connection A66-9 (OPM1) - A65-8 (GND)
Tool Setting 5 V/DIV.,5 ms./DIV.
Condition Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed




f.
A318633E03
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND 0.26,0.073 1.49,0.271 1.229,0.198 10 false 5 V/DIV. 1.313,1.906 2.844,2.104 1.531,0.198 10 false 2 ms./DIV.

Waveform 2

Item Content
Tester Connection A66-10 (NE) - A65-8 (GND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up


g.
A112562E03
2.844,1.219 3.156,1.375 0.313,0.156 10 false GND 0.094,0.042 1.177,0.344 1.083,0.302 10 false 5 V/DIV. 1.25,1.99 2.323,2.177 1.073,0.188 10 false 5 ms./DIV.

Waveform 3

Item Content
Tester Connection A66-27 (NOPM) - A65-8 (GND)
Tool Setting 5 V/DIV.,5 ms./DIV.
Condition Either of the following conditions is met:
·

Engine stopped by stop and start control

·

Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed