If any of the following DTCs are stored, the engine stop and start ECU enters fail-safe mode to preserve vehicle operability.
| DTC | Component | Fail-safe Operation | Fail-safe Deactivation Condition |
|---|---|---|---|
| B22C0 | Backup boost converter circuit | Stop and start control is prohibited | ·
Pass condition detected and ignition switch turned to ON ·
DTCs (for overcurrent caused by audio volume setting) are cleared |
| P0335 | Open in engine speed signal circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
All of the following conditions are met for 10 seconds:
·
Normal communication with ECM ·
Engine speed 500 rpm or higher ·
Engine speed (communication signal) 500 rpm or higher ·
Difference between engine speed from pulse signal and engine speed from communication signal is less than 100 rpm |
| P0560 | Open in VB circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P0562 | ·
Power source circuit ·
Low battery voltage |
·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Both of the following conditions are met for at 3 seconds or more while the engine is stopped by stop and start control and the generator is not generating electricity:
·
+B voltage 11.5 V or higher ·
Engine stopped |
| P0607 | Engine stop and start ECU | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P060A | Engine stop and start ECU | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P060B | Analog to digital converter (Engine stop and start ECU) | ·
Stop and start control is prohibited ·
Engine stalls |
Pass condition detected and ignition switch turned to ON |
| P0617 | ST relay circuit | Stop and start control is prohibited | Pass condition detected and DTCs are cleared |
| P062F | Engine stop and start ECU | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Number of starter operations and air conditioning information are registered correctly |
| P0641 | Engine stop and start ECU | ·
Stop and start control is prohibited ·
Engine stalls |
Pass condition detected and ignition switch turned to ON |
| P0942 | Oil pump assembly with motor (Continuously variable transaxle assembly) circuit | Stop and start control is prohibited | Pass condition detected and DTCs are cleared |
| P1538
P1539 |
Oil pump assembly with motor (Continuously variable transaxle assembly) circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P1540 | Vacuum sensor assembly circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Sensor output is within standard range |
| P1541 | ·
Vacuum sensor assembly ·
Brake booster assembly ·
Check valve to connector tube hose (brake booster hose) |
·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Either of the following conditions is met:
·
Vacuum changes while the brake pedal is depressed ·
Vacuum changes a specified number of times while the vehicle is being driven faster than a certain vehicle speed |
| P1545 | ·
Starter assembly ·
Starter circuit |
·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
·
DTCs and number of starter operations stored in the ECU (after replacing the starter) are cleared ·
Communication with ECM returns to normal and either of the following conditions (a) or (b) is met: 1.
The STA signal detected by the ECM and STA and STA2 signals detected by the engine stop and start ECU are ON for 0.3 seconds and "Tandem Starter" displayed for "Starter Type" in the Data List 2.
The STA signal detected by the ECM and STA and STA2 signals detected by the engine stop and start ECU are ON for 5 seconds and "Tandem Starter" displayed for "Starter Type" in the Data List. |
| P1589 | G sensor zero point calibration incomplete | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P161D | Starter delay circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
·
Pass condition detected and ignition switch turned to ON ·
Time between STA (for starter pinion) turning on and STA2 (for starter motor) turning on becomes 0.016 seconds or more |
| P1644 | ·
Starter drive circuit ·
ST NO. 1 relay ·
ST NO. 2 relay ·
Engine stop and start ECU |
·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Voltage of engine stop and start ECU internal drive circuit for starter is correct when engine is idling and restarted |
| P1780 | Park/neutral position switch assembly circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| P2531 | IG signal circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Both of the following conditions are met for 10 seconds or more:
·
Ignition switch ON ·
Normal communication with ECM |
| P323B | Backup boost converter circuit | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Pass condition detected and ignition switch turned to ON |
| U0100 | CAN communication (ECM) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 1.52 seconds |
| U0121 | CAN communication (skid control ECU (brake actuator assembly)) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 4.44 seconds |
| U0126 | CAN communication (spiral with sensor cable sub-assembly) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 1.44 seconds |
| U0131 | CAN communication (power steering ECU assembly) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 1.6 seconds |
| U0140 | CAN communication (main body ECU (multiplex network ECU)) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 7.2 seconds |
| U0151 | CAN communication (airbag sensor assembly) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds |
| U0155 | CAN communication (combination meter assembly) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds. |
| U0164 | CAN communication (air conditioning amplifier) | ·
Stop and start control is prohibited ·
Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control |
Communication with engine stop and start ECU continues for 21.2 seconds |