The engine stop and start ECU monitors +B terminal voltage while the engine is stopped by stop and start control. If the voltage drops below the specified level, the engine stop and start ECU stores DTC P0562 and blinks the stop and start cancel indicator light.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P0562 | System Voltage Low | Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
·
+B terminal voltage is 9 V or less. ·
Engine stop by stopped and start control |
·
Battery ·
Wire harness or connector ·
EFI-MAIN NO. 1 relay ·
Engine stop and start ECU |
Blinks | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that DTCs are not output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Allow the engine to stop by stop and start control. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Turn off all electrical systems.
Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.
| Tester Display |
|---|
| Battery Voltage |
Read the battery voltage displayed on the GTS screen.
| Result | Proceed to |
|---|---|
| 9 to 14 V | A |
| Below 9 V | B |
A
B
Inspect the EFI-MAIN NO. 1 relay.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A65-5 (+B) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG