Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

The engine stop and start ECU stores the number of starter assembly operations, air conditioning information, and the deceleration sensor zero point learning results.

If the engine stop and start ECU cannot write the number of starter assembly operations, air conditioning information, or the deceleration sensor zero point learning results, it stores DTC P062F, blinks the stop and start cancel indicator light, and prohibits stop and start control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P062F Internal Control Module EEPROM Error Any of the following conditions are met (1 trip detection logic):
·

Air conditioning information cannot be written

·

The deceleration sensor zero point learning value cannot be written

·

The number of starter operations was not successfully written to the EEPROM.


Engine stop and start ECU Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA


PROCEDURE

1.PERFORM REGISTRATION (ECU EXCHANGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility
Tester Display
ECU Exchange
50005 227 131

e.

According to the display on the GTS, download the previous status (the number of starter operations) from the engine stop and start ECU to the GTS.


Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


b.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 227

Result:
Proceed to
NEXT



NEXT

3.PERFORM REGISTRATION (STARTER EXCHANGE, RESET A/C INFORMATION, DECELERATION SENSOR ZERO POINT CLEAR)
3.PERFORM REGISTRATION (STARTER EXCHANGE, RESET A/C INFORMATION, DECELERATION SENSOR ZERO POINT CLEAR)
a.

Clear the number of starter operations.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Starter Exchange.

Powertrain > Stop and Start > Utility
Tester Display
Starter Exchange
50005 227 130


b.

Clear the air conditioning information.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Reset A/C Information.

Powertrain > Stop and Start > Utility
Tester Display
Reset A/C Information
50005 227 2104


c.

Clear the zero point calibration data of the deceleration sensor.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

Powertrain > Stop and Start > Utility
Tester Display
Deceleration Sensor Zero Point Clear
50005 227 4174


Result:
Proceed to
NEXT



NEXT

4.PERFORM REGISTRATION (ECU EXCHANGE)
4.PERFORM REGISTRATION (ECU EXCHANGE)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility
Tester Display
ECU Exchange
50005 227 131

b.

According to the prompts on the GTS screen, write the information to the engine stop and start ECU.


c.

Perform air conditioning information learning.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

HINT:

When initialization of the air conditioning information is complete, air conditioning information learning is automatically performed.



d.

Perform deceleration sensor zero point calibration.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

Powertrain > Stop and Start > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 227 4147


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.


g.

Check for DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227

h.

Check the number of starter operations.

Powertrain > Stop and Start > Data List
Tester Display
Starter Operation #
50003 227 56
Result:
Result Proceed to
DTCs are not output A
DTC P062F is output B




A

END

B