Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P1538  Circuit Malfunction between AT Oil Pump and Stop and Start ECU  


DESCRIPTION

The oil pump of the continuously variable transaxle assembly stops operating when the engine is stopped by stop and start control. While the engine is stopped by stop and start control, the oil pump assembly with motor is operated continuously ensuring optimal CVT oil pressure and smooth start-off when the engine is restarted.

The engine stop and start ECU supplies power to the oil pump assembly via terminal OPO and operates the oil pump assembly with motor in accordance with signals sent from terminal OPM1. The oil pump assembly with motor sends operating speed signals to the engine stop and start ECU via the NOPM signal line.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1538 Circuit Malfunction between AT Oil Pump and Stop and Start ECU Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
·

Oil pump motor relay circuit in the engine stop and start ECU is off

·

Oil pump assembly with motor power supply malfunction (Oil pump motor relay circuit in the engine stop and start ECU stuck on or shorted) or a short to ground in the NOPM circuit*1


Both of the following conditions are met for 1 second or more (2 trip detection logic):
·

Engine started

·

Oil pump assembly with motor circuit malfunction (Oil pump motor relay in the engine stop and start ECU stuck off, open or short to ground in the OPO, OPM1 or NOPM circuit or an open in the GND circuit)*2


·

Wire harness or connector

·

Oil pump assembly with motor (Continuously variable transaxle assembly)

·

Engine stop and start ECU


Blinks DTC stored

*1: "Abnormal" is displayed for the freeze frame data item [Status of O/P Signal 1]

*2: "Abnormal" is displayed for the freeze frame data item [Status of O/P Signal 2]

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



WIRING DIAGRAM

A337511E04
0.25,2.833 1.021,3.031 0.771,0.198 10 false B92 0.25,3.073 3.604,3.49 3.354,0.417 10 false Oil Pump Assembly with Motor (Continuously Variable Transaxle Assembly) 4.458,2.802 6.281,3.052 1.823,0.25 10 false Engine Stop and Start ECU 4.385,0.854 4.844,1.052 0.458,0.198 10 false A65 4.438,0.656 4.594,0.854 0.156,0.198 10 false 6 4.396,1.323 4.854,1.521 0.458,0.198 10 false A66 4.396,2.24 4.854,2.438 0.458,0.198 10 false A65 4.385,1.781 4.844,1.979 0.458,0.198 10 false A66 4.448,1.125 4.604,1.323 0.156,0.198 10 false 9 4.417,1.573 4.729,1.771 0.313,0.198 10 false 27 4.458,2.052 4.615,2.25 0.156,0.198 10 false 8 4.75,0.729 5.208,0.927 0.458,0.198 10 false OPO 4.76,1.208 5.375,1.406 0.615,0.198 10 false OPM1 4.76,1.896 5.375,2.094 0.615,0.198 10 false NOPM 4.76,2.25 5.219,2.448 0.458,0.198 10 false GND 2.135,0.854 2.448,1.052 0.313,0.198 10 false +B 2.177,1.219 2.49,1.417 0.313,0.198 10 false SI 1.958,1.667 2.573,1.865 0.615,0.198 10 false OPST 2.063,2.24 2.521,2.438 0.458,0.198 10 false GND 2.49,0.729 2.646,0.927 0.156,0.198 10 false 4 2.479,1.188 2.635,1.385 0.156,0.198 10 false 3 2.49,1.646 2.646,1.844 0.156,0.198 10 false 2 2.49,2.094 2.646,2.292 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

Bleed the oil pump assembly with motor (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA


PROCEDURE

1.CHECK FREEZE FRAME DATA
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


a.

According to the display on the GTS, select DTC P1538 and check the sets of freeze frame data.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA

Result:
Tester Display Result Proceed to
Status of O/P Signal 1 Abnormal A
Status of O/P Signal 2 Abnormal B




A

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)

B

4.PERFORM ACTIVE TEST USING GTS (AT OIL PUMP (LO))
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)
a.

Disconnect the A65 and A66 engine stop and start ECU connectors.


b.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-27 (NOPM) - B92-2 (OPST) Always Below 1 Ω
A65-6 (OPO) - B92-4 (+B) Always Below 1 Ω
A66-27 (NOPM) - Body ground Always 10 kΩ or higher
B92-2 (OPST) - Body ground Always 10 kΩ or higher
A65-6 (OPO) - Body ground Always 10 kΩ or higher
B92-4 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (NOPM TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (NOPM TERMINAL VOLTAGE)
a.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.

A350366C04
1.927,0.771 2.396,1.052 0.469,0.281 3.146,0.771 3.615,1.052 0.469,0.281 2.01,1.708 1.76,2.344 true 2.896,1.698 3.052,2.354 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.563,2.396 2.01,2.583 0.448,0.188 10 false GND 2.031,0.844 2.365,1.042 0.333,0.198 10 false A65 3.26,0.844 3.594,1.042 0.333,0.198 10 false A66 2.875,2.396 3.49,2.594 0.615,0.198 10 false NOPM
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-27 (NOPM) - A65-8 (GND) Ignition switch ON 10 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

4.PERFORM ACTIVE TEST USING GTS (AT OIL PUMP (LO))
a.

Drive the vehicle to warm up the engine and CVT fluid.

HINT:

The oil pump assembly with motor (continuously variable transaxle assembly) may not operate properly if the CVT fluid temperature is low. Make sure to warm up the CVT fluid before performing the Active Test. (CVT fluid temperature: 30°C (86°F) or higher)



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Active Test / AT Oil Pump (Lo).

Powertrain > Stop and Start > Active Test
Tester Display
AT Oil Pump (Lo)
50004 227 11

f.

Check the operating sound of the oil pump assembly with motor (continuously variable transaxle assembly) while performing the Active Test.

Standard:
AT Oil Pump (Lo) Result
ON Operating sound can be heard
OFF Operating sound cannot be heard



Result:
Proceed to
OK
NG



OK

5.CHECK ENGINE STOP AND START ECU (NOPM TERMINAL WAVEFORM)

NG

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)
5.CHECK ENGINE STOP AND START ECU (NOPM TERMINAL WAVEFORM)
a.

Connect an oscilloscope to terminals A66-27 (NOPM) and A65-8 (GND).

A350366C04
1.927,0.771 2.396,1.052 0.469,0.281 3.146,0.771 3.615,1.052 0.469,0.281 2.01,1.708 1.76,2.344 true 2.896,1.698 3.052,2.354 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.563,2.396 2.01,2.583 0.448,0.188 10 false GND 2.031,0.844 2.365,1.042 0.333,0.198 10 false A65 3.26,0.844 3.594,1.042 0.333,0.198 10 false A66 2.875,2.396 3.49,2.594 0.615,0.198 10 false NOPM
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Enter the following menus: Powertrain / Stop and Start / Active Test / AT Oil Pump (Lo).

Powertrain > Stop and Start > Active Test
Tester Display
AT Oil Pump (Lo)
50004 227 11

c.
A112562E03
2.844,1.219 3.156,1.375 0.313,0.156 10 false GND 0.094,0.042 1.177,0.344 1.083,0.302 10 false 5 V/DIV. 1.25,1.99 2.323,2.177 1.073,0.188 10 false 5 ms./DIV.

Check the waveform while performing the Active Test.

Item Condition
Tester Connection A66-27 (NOPM) - A65-8 (GND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition
·

Ignition switch ON (engine is stopped)

·

Active Test "AT Oil Pump (Lo)" being performed



Standard:

The waveform is similar to that shown in the illustration with no noise.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK OIL PUMP ASSEMBLY WITH MOTOR (OPST TERMINAL VOLTAGE)
6.CHECK OIL PUMP ASSEMBLY WITH MOTOR (OPST TERMINAL VOLTAGE)
a.
A319122C05
0.583,1.26 0.969,1.5 0.385,0.24 1.167,1.917 1.375,1.542 false 1.844,1.917 1.677,1.542 false 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 0.667,1.302 1.125,1.5 0.458,0.198 10 false B92 1.021,1.948 1.479,2.146 0.458,0.198 10 false GND 1.698,1.948 2.313,2.146 0.615,0.198 10 false OPST
*a Front view of wire harness connector
(to Oil Pump Assembly with Motor (Continuously Variable Transaxle Assembly))


Disconnect the oil pump assembly with motor (continuously variable transaxle assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B92-2 (OPST) - B92-1 (GND) Ignition switch ON 10 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)
7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-27 (NOPM) - B92-2 (OPST) Always Below 1 Ω
A66-27 (NOPM) - Body ground Always 10 kΩ or higher
B92-2 (OPST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)
a.

Disconnect the A65 engine stop and start ECU connector.


b.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-6 (OPO) - B92-4 (+B) Always Below 1 Ω
A65-6 (OPO) - Body ground Always 10 kΩ or higher
B92-4 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (OIL PUMP ASSEMBLY WITH MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (OIL PUMP ASSEMBLY WITH MOTOR - BODY GROUND)
a.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B92-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK ENGINE STOP AND START ECU (OPO TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK ENGINE STOP AND START ECU (OPO TERMINAL VOLTAGE)
a.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.


A350366C05
1.927,0.771 2.396,1.052 0.469,0.281 2.01,1.708 1.76,2.344 true 2.479,1.76 3.052,2.354 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.563,2.396 2.01,2.583 0.448,0.188 10 false GND 2.031,0.844 2.365,1.042 0.333,0.198 10 false A65 2.917,2.396 3.531,2.594 0.615,0.198 10 false OPO
*a Component with harness connected
(Engine Stop and Start ECU)
- -


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Active Test / AT Oil Pump (Lo).

Powertrain > Stop and Start > Active Test
Tester Display
AT Oil Pump (Lo)
50004 227 11

f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-6 (OPO) - A65-8 (GND)
·

Ignition switch ON (engine is stopped)

·

Active Test "AT Oil Pump (Lo)" being performed


10.5 to 16 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)

NG

11.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OIL PUMP ASSEMBLY WITH MOTOR)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the B92 oil pump assembly with motor (continuously variable transaxle assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-9 (OPM1) - B92-3 (SI) Always Below 1 Ω
A66-9 (OPM1) - Body ground Always 10 kΩ or higher
B92-3 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK OIL PUMP ASSEMBLY WITH MOTOR (OPM1 TERMINAL WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK OIL PUMP ASSEMBLY WITH MOTOR (OPM1 TERMINAL WAVEFORM)
a.

Connect an oscilloscope to the A66-9 (OPM1) and A65-8 (GND) terminals of the engine stop and start ECU connector.

A350366C06
1.927,0.771 2.396,1.052 0.469,0.281 3.146,0.771 3.615,1.052 0.469,0.281 2.01,1.708 1.76,2.344 true 2.969,1.594 3.052,2.354 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.563,2.396 2.01,2.583 0.448,0.188 10 false GND 2.031,0.844 2.365,1.042 0.333,0.198 10 false A65 3.26,0.844 3.594,1.042 0.333,0.198 10 false A66 2.875,2.396 3.49,2.594 0.615,0.198 10 false OPM1
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Active Test / AT Oil Pump (Lo).

Powertrain > Stop and Start > Active Test
Tester Display
AT Oil Pump (Lo)
50004 227 11

f.
A329962E01
0.073,0.052 1.302,0.25 1.229,0.198 10 false 5 V/DIV. 1.135,2 1.958,2.177 0.823,0.177 10 false 5 ms./DIV. 2.885,1.25 3.344,1.448 0.458,0.198 10 false GND

Check the waveform while performing the Active Test.

Item Condition
Tester Connection A66-9 (OPM1) - A65-8 (GND)
Tool Setting 5 V/DIV., 5 ms./DIV.
Condition
·

Ignition switch ON (engine is stopped)

·

Active Test "AT Oil Pump (Lo)" being performed



Standard:

The waveform is similar to that shown in the illustration with no noise.



Result:
Proceed to
OK
NG



OK

NG

REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY