If the engine stop and start ECU receives the off signal from the certification ECU (smart key ECU assembly) when communication with the ECM is normal, the engine stop and start ECU will store DTC P2531.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P2531 | Ignition Switch Run Position Circuit Low | Both of the following conditions are met for 10 seconds or more (1 trip detection logic):
·
Ignition switch off signal is input. ·
Communication with the ECM is normal. |
·
Wire harness or connector ·
IG2 relay ·
EFI-MAIN NO. 1 relay ·
Certification ECU (Smart key ECU assembly) ·
Engine stop and start ECU |
Does not come on | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Keep the engine stopped by stop and start control for 10 second or more. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
Check that DTCs are not output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Allow the engine to stop by stop and start control. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| IG Switch |
| Tester Display | Result | Proceed to |
|---|---|---|
| IG Switch | ON | A |
| OFF | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the G87 engine stop and start ECU connector.
Remove the IG2 relay from engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G87-20 (IG2) - IG2 relay terminal 5 | Always | Below 1 Ω |
| G87-20 (IG2) - Body ground | Always | 10 kΩ or higher |
| IG2 relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the IG2 relay.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay from engine room relay block and junction block assembly.
w/ Entry and Start System:
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
w/o Entry and Start System:
Disconnect the G4 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 1 - G82-9 (IG2D) | Always | Below 1 Ω |
| IG2 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| G82-9 (IG2D) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 relay terminal 1 - G4-3 (IG2) | Always | Below 1 Ω |
| IG2 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| G4-3 (IG2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A65 engine stop and start ECU connector.
Remove the EFI-MAIN NO. 1 relay from engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A65-5 (+B) - EFI-MAIN NO. 1 relay terminal 3 | Always | Below 1 Ω |
| A65-5 (+B) - Body ground | Always | 10 kΩ or higher |
| EFI-MAIN NO. 1 relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-6 (IGSW) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO. 1 relay.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If communication between the GTS and vehicle is possible and SFI system data can be read 30 seconds after turning the ignition switch off a malfunction in the EFI-MAIN NO. 1 relay circuit is suspected.
Remove the EFI-MAIN NO. 1 relay from engine room relay block and junction block assembly.
Disconnect the A62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI-MAIN NO. 1 relay terminal 1 - A62-46 (MREL) | Always | Below 1 Ω |
| EFI-MAIN NO. 1 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| A62-46 (MREL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK (w/ Entry and Start System) |
| OK (w/o Entry and Start System) |
| NG |
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-9 (IG2D) - Body ground | Ignition switch ACC | Below 1 V |
| G82-9 (IG2D) - Body ground | Ignition switch ON | 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>3ZR-FAE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG