Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2015.04–2015.10
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM U

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.



Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

·

Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.


Engine Speed Engine speed min.: 0 rpm
max.: 16383 rpm
600 to 700 rpm: Idling When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
N Range Status Judgment for shift lever N position ON or OFF
·

OFF: Shift lever not in N

·

ON: Shift lever in N


-
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Stop Light Switch Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
SPD (NT) Input turbine speed min.: 0 rpm
max.: 12750 rpm
·

Lock-up on (After warming up engine): Input turbine speed (NT) equal to engine speed

·

Lock-up off (Idling with shift lever in P or N): Input turbine speed (NT) nearly equal to engine speed

·

Vehicle stopped with shift lever in R: 0 rpm


Data is displayed in increments of 50 rpm.
Overdrive Cut Switch #1 Overdrive cut switch No. 1 status OFF or ON - -
Shift SW Status (P Range) PNP switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Pattern Switch (PWR/M) Sport mode status* ON or OFF
·

ON: Sport mode on

·

OFF: Sport mode off


-
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N,P Range) Supported Status of PNP switch (N or P) support Supp or Unsupp - -
Shift SW Status (N,P Range) PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


-
Sports Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
A/T Oil Temperature 1 CVT fluid temperature sensor value min.: -40°C (-40°F)
max.: 215°C (419°F)
·

After stall speed test: Approx. 100°C (212°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted.
NT Sensor Voltage Input turbine speed (NT) sensor output voltage min.: 0 V
max.: 4.999 V
Engine idling (Vehicle stopped with shift lever in P or N): 0.6 to 1.5 V -
SPD (NIN) Primary pulley speed (NIN) min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed


Data is displayed in increments of 50 rpm.
SPD (NOUT) Secondary pulley speed (NOUT) min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Vehicle cruising at approx. 60 km/h (37 mph): 2650 rpm


Data is displayed in increments of 50 rpm.
NOUT Sensor Voltage Secondary pulley speed (NOUT) sensor output voltage min.: 0.000 V
max.: 4.999 V
Engine idling: Approx. 2 V -
A/T Oil Pressure Secondary oil pressure value min.: -64 MPa
max.: 63.998 MPa
Secondary oil pressure inspection
·

D position stall speed test: 3.2 to 4.5 MPa

·

R position stall speed test: 3.0 to 3.5 MPa


-
G Sensor Converted output voltage of deceleration sensor min.: 0 V
max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-
Solenoid (DSU) Shift solenoid valve DSU status ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Lock Up Lock-up ON or OFF
·

ON: Lock-up operating

·

OFF: Lock-up not operating


-
Shift Status ECM gearshift command 1st, 2nd, 3rd, 4th or 5th Same as actual gear -
Solenoid (DS2) Shift solenoid valve DS2 status ON or OFF
·

OFF: Constant cruising with shift lever in D

·

ON: Accelerator pedal depressed further after cruising with shift lever in D


-
Solenoid (DS1) Shift solenoid valve DS1 status ON or OFF
·

ON: Driving with shift lever in D and accelerator pedal depressed

·

OFF: Accelerator pedal released when driving with shift lever in D with accelerator pedal depressed


-
Solenoid (SLS) Shift solenoid valve SLS status ON or OFF
·

ON: After engine start

·

OFF: Ignition switch ON


-
SL Solenoid Status Shift solenoid valve SL status ON or OFF
·

Shift solenoid valve SL on: ON

·

Shift solenoid valve SL off: OFF


-
G Sensor Calibration G sensor calibration status Incomplete or Complete Complete -
G Sensor Learning Value G sensor learned value voltage min.: 0 V
max.: 79.998 V
G sensor calibration is complete: 2.31 V to 2.69 V -
CVT Oil Press Calibration CVT oil pressure calibration status Incomplete or Complete Complete -

*: w/ Combination Switch (SPORT)

ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Connect the TC and TE1 Turn on and off TC and TE1 connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


[Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P.
Activate the Lock Up Operate lock-up ON or OFF Possible to check lock-up operation.
HINT:

Perform "Activate the Lock Up" while monitoring the engine speed (ESPD) and turbine speed (NT).


[Vehicle Condition]
Perform at a vehicle speed of 60 km/h (37 mph) or more.
Activate the Solenoid (SL) Operate shift solenoid valve SL ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Control the Shift Position Operate the shift solenoid valves to allow the gear ratio to be manually selected [1st - 2nd - 3rd - 4th - 5th]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.


[Vehicle Condition]
Perform at a vehicle speed of 20 km/h (12 mph) or more and 45 km/h (28 mph) or less.
Activate the Solenoid (DSU) Operate shift solenoid valve DSU ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Activate the Solenoid (DS1) Operate shift solenoid valve DS1 ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Activate the Solenoid (DS2) Operate shift solenoid valve DS2 ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.
Control the SLS Pressure Operate shift solenoid valve SLS High or Low [Vehicle Condition]
Perform with the ignition switch ON and the engine running.
Activate the Solenoid (SLS) Operate shift solenoid valve SLS ON or OFF [Vehicle Condition]
Perform with the ignition switch ON, the engine stopped and shift lever in P or N.