The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is detected by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0842 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Low | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
2 seconds or more have elapsed after the engine is started. 2.
There is a short circuit in the oil pressure sensor circuit. 3.
0.5 seconds 4.
1 trip detection logic |
·
Short in oil pressure sensor circuit ·
Oil pressure sensor ·
ECM |
Comes on (w/ OBD)
- (w/o OBD) |
DTC stored |
| P0843 | Transmission Fluid Pressure Sensor/Switch "A" Circuit High | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
2 seconds or more have elapsed after the engine is started. 2.
There is an open circuit in the oil pressure sensor circuit. 3.
0.5 seconds 4.
1 trip detection logic |
·
Open in oil pressure sensor circuit ·
Oil pressure sensor ·
ECM |
Comes on (w/ OBD)
- (w/o OBD) |
DTC stored |
These DTCs indicate an open or short circuit in the oil pressure sensor circuit. When there is an open or short circuit in the oil pressure sensor circuit, the ECM detects the problem, illuminates the MIL and stores the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| A/T Oil Pressure |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | min.: -64 MPa
max.: 63.998 MPa |
Secondary oil pressure inspection
·
D position stall speed test: 3.2 to 4.5 MPa ·
R position stall speed test: 3.0 to 3.5 MPa |
- |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is not as specified under Normal Condition |
| Data displayed is as specified under Normal Condition |
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition
Disconnect the B32 oil pressure sensor connector.
Disconnect the B75 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B32-1 (E2) - B75-121 (EPTO) | Always | Below 1 Ω |
| B32-2 (PTO) - B75-89 (PTO) | Always | Below 1 Ω |
| B32-3 (VC) - B75-120 (VCPT) | Always | Below 1 Ω |
| B32-1 (E2) or B75-121 (EPTO) - Body ground | Always | 10 kΩ or higher |
| B32-2 (PTO) or B75-89 (PTO) - Body ground | Always | 10 kΩ or higher |
| B32-3 (VC) or B75-120 (VCPT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Oil Pressure Sensor) |
Disconnect the oil pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B32-1 (E2) - B32-3 (VC) | Ignition switch ON | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sensor.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT