Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.04–2015.10
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1247 Tire Pressure Monitor Receiver Communication Stop In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (multiplex network body ECU)

·

ECU-IG NO. 2 fuse*1

·

Backup boost converter circuit*2



*1: w/o Stop and Start System

*2: w/ Stop and Start System


WIRING DIAGRAM

C279316E04
4.031,0.427 6.323,0.625 2.292,0.198 10 false from IG Circuit 2.469,0.594 4.76,0.792 2.292,0.198 10 false ECU-IG NO. 2 1.417,0.427 1.813,0.635 0.396,0.208 10 false IG 1.219,1.708 1.76,2.104 0.542,0.396 10 false RDA2 1.292,2.688 1.813,3.094 0.521,0.406 10 false GND 0.156,3.104 0.594,3.302 0.438,0.198 10 false M30 1.208,2.24 1.771,2.573 0.563,0.333 10 false PRG2 0.146,3.302 2.833,3.604 2.688,0.302 10 false Tire Pressure Warning ECU and Receiver 1.75,0.26 2.146,0.469 0.396,0.208 10 false 1 1.781,1.563 2.177,1.771 0.396,0.208 10 false 4 1.771,2.042 2.167,2.25 0.396,0.208 10 false 5 1.75,2.51 2.146,2.719 0.396,0.208 10 false 12 5.823,1.698 6.281,1.896 0.458,0.198 10 false RDA 5.823,2.219 6.281,2.417 0.458,0.198 10 false PRG 5.521,1.531 5.813,1.771 0.292,0.24 10 false 16 5.563,2.031 5.854,2.271 0.292,0.24 10 false 4 5.458,3.125 5.917,3.323 0.458,0.198 10 false G78 5.469,3.323 7.135,3.76 1.667,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 0.156,3.781 3.365,3.979 3.208,0.198 10 false *1: w/o Stop and Start System 0.167,4.125 3.375,4.323 3.208,0.198 10 false *2: w/ Stop and Start System 3.979,1.042 4.469,1.385 0.49,0.344 10 false IGO1 3.323,1.354 3.781,1.552 0.458,0.198 10 false G87 3.635,1.354 5.552,1.771 1.917,0.417 10 false Engine Stop and Start ECU*2 3.708,0.865 4,1.104 0.292,0.24 10 false 12 2.833,0.917 3.188,1.25 0.354,0.333 10 false *2 2.313,0.323 2.667,0.656 0.354,0.333 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the tire pressure warning ECU and receiver M30 connector and main body ECU (multiplex network body ECU) G78 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-4 (RDA2) - G78-16 (RDA) Always Below 1 Ω
M30-4 (RDA2) or G78-16 (RDA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the tire pressure warning ECU and receiver M30 connector.


b.
E198671C27
0.25,0.927 0.667,1.198 0.417,0.271 1.24,1.427 0.5,1.583 0.5,1.583 0.5,1.75 true 2.063,1.625 2.49,1.667 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.333,1 0.792,1.198 0.458,0.198 10 false M30 0.448,1.771 0.76,1.969 0.313,0.198 10 false IG 2.563,1.594 3.302,1.771 0.74,0.177 10 false GND
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-12 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M30-1 (IG) - Body ground Ignition switch ON 10 to 16 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (B1247)
4.CHECK DTC OUTPUT (B1247)
a.

Clear the DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1247 is not output.


Result:
Proceed to
OK
NG




OK

END

NG