Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2015.04–2015.10
RM3090E _53 Suspension _008691 TIRE PRESSURE MONITORING _0048202 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C279317E05
0.938,0.438 2.156,0.656 1.219,0.219 10 false from IG Circuit 3.146,0.625 4.365,0.844 1.219,0.219 10 false ECU-IG NO. 2 0.354,1.948 2.281,2.219 1.927,0.271 10 false *1: w/o Stop and Start System 0.365,2.313 2.26,2.594 1.896,0.281 10 false *2: w/ Stop and Start System 4.802,0.292 5.073,0.552 0.271,0.26 10 false 1 4.74,1.479 5.01,1.74 0.271,0.26 10 false 12 5.052,0.438 5.458,0.646 0.406,0.208 10 false IG 5.01,1.635 5.563,1.844 0.552,0.208 10 false GND 4.583,2.135 4.958,2.344 0.375,0.208 10 false M30 4.583,2.313 7.156,2.708 2.573,0.396 10 false Tire Pressure Warning ECU and Receiver 0.74,1.417 2.885,1.719 2.146,0.302 10 false Engine Stop and Start ECU*2 0.417,1.417 0.906,1.688 0.49,0.271 10 false G87 3.052,0.969 3.323,1.229 0.271,0.26 10 false *2 1.51,1.094 2,1.354 0.49,0.26 10 false IGO1 1.969,0.958 2.24,1.219 0.271,0.26 10 false 12 4.01,0.292 4.281,0.552 0.271,0.26 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click here Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU - BATTERY AND BODY GROUND)
a.
E198671C27
0.25,0.927 0.667,1.198 0.417,0.271 1.24,1.427 0.5,1.583 0.5,1.583 0.5,1.75 true 2.063,1.625 2.49,1.667 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.333,1 0.792,1.198 0.458,0.198 10 false M30 0.448,1.771 0.76,1.969 0.313,0.198 10 false IG 2.563,1.594 3.302,1.771 0.74,0.177 10 false GND
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the tire pressure warning ECU and receiver M30 connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M30-1 (IG) - Body ground Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M30-12 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)